manualshive.com logo in svg

Spectris Particle Measuring Systems LiQuilaz II E, Руководство по эксплуатации

Поделиться
Скачать
Spectris Particle Measuring Systems LiQuilaz II E Скачать руководство пользователя страница 26

Chapter 2 Unpacking and Connection

LiQuilaz II E and S Operations Manual

Page 2-11

Communication Options

The LiQuilaz II offers multiple communication options.

Facility Net 

Connect using Ethernet or RS-485. When communicating via Ethernet, Facility Net V4.0 
or newer is recommended. V3.3 can be used by setting Retro mode in the  
 LiQuilaz II. This causes the instrument to appear as a HSLIS sensor so that it can be 
recognized by the older Facility Net version. Please see 

“set inst(rument) retro n” 

on 

page

  G-3 in 

Appendix

 

G

, Serial Setup Command List.

Ethernet communication settings and options must be set via RS-232 setup commands 
in 

Appendix

 

E

, Configuring for Ethernet.

SamplerSight or SamplerSight Pharma

Connect using RS-485. An opto-isolated RS-485 to USB adaptor with a 10ft RS-485 
cable to the LiQuilaz II is available (P/N 1000021389). 

SamplerSight software can only operate one sensor at a time. If more than one sensor 
must be connected via RS-485 via daisy-chain, use FacilityNet software instead.

Modbus TCP

Connect using Ethernet. Communication settings and options must be set via RS-232 
setup commands in 

Appendix

 

E

, Configuring for Ethernet. Modbus protocol is an 

industry standard protocol that is provided for customers who need to interface to a 
custom computer program or SCADA system. By default the LiQuilaz II is configured 
with Modbus disabled. Use serial command 

“set mode 1”

 as described in 

Appendix

 

G

, 

Serial Setup Command List to enable Modbus. The Modbus protocol for the LiQuilaz II 
is described in 

Appendix

 

C

, Modbus TCP Protocol.

RS-232

This is primarily a configuration interface to program the LiQuilaz II for the 
communication methods mentioned above. An RS-232 adaptor pigtail (P/N PMS-
CD1995) and a USB to RS-232 adaptor (P/N 1000023262) are supplied as accessories to 
the LiQuilaz II to facilitate setup. Please see 

Appendix

 

G

, Serial Setup Command List 

for serial commands and 

Appendix

 

F

, Serial Communications Overview for basic serial 

communications information if necessary.

Содержание Particle Measuring Systems LiQuilaz II E














































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды