manualshive.com logo in svg

Spectris Particle Measuring Systems LiQuilaz II E, Руководство по эксплуатации

Поделиться
Скачать
Spectris Particle Measuring Systems LiQuilaz II E Скачать руководство пользователя страница 30

Chapter 3 Maintenance

LiQuilaz II E and S Operations Manual

Page 3-3

Capillary Cleaning (Online Version, E and S Series)

>> To clean the capillary: 

1.

Turn off and unplug the particle counter.

2.

Isolate the liquid particle counter from its fluid source.

3.

Disconnect the sample inlet and outlet fittings.

OUT

IN

Figure 3-1  

LiQuilaz II fittings

4.

Fill each syringe from the capillary cleaning kit with 5 ml of cleaning solution mixed 
to the recommended strength.

Figure 3-2  

Capillary Cleaning Kit syringes

5.

Connect the filled syringes to the particle counter’s sample inlet and outlet 
connections.

6.

Press one syringe plunger all the way into the syringe cylinder. 

7.

Force the cleaning solution back and forth between the two syringes for 30 seconds 
to 1 minute.

Содержание Particle Measuring Systems LiQuilaz II E














































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды