manualshive.com logo in svg

Spectris Particle Measuring Systems LiQuilaz II E, Руководство по эксплуатации

Поделиться
Скачать
Spectris Particle Measuring Systems LiQuilaz II E Скачать руководство пользователя страница 3

ii 

LiQuilaz II E and S Operations Manual

LiQuilaz

®

 II E and S Series Particle Counters Operations Manual 

P/N 1000023550 Rev C 
© 2019 by Particle Measuring Systems, Inc. 
All rights reserved.

LiQuilaz

®

 is a registered trademark of Particle Measuring Systems, Inc. 

Flaretek

®

 is a registered trademark of Entegris, Inc. 

Teflon

®

 is a registered trademark of E.I. du Pont de Nemours and Company.

All trademarks appearing in this manual are the property of their respective owners. 

DO NOT REPRODUCE OR DISTRIBUTE

CONFIDENTIAL DOCUMENT

This confidential document contains proprietary information, which is protected by 
copyright. All rights are reserved. No part of this document may be reproduced, 
distributed, or transmitted in any form without the prior written consent of Particle 
Measuring Systems. The information contained in this document is subject to change 
without notice.

Quality Statement

The Quality Policy of Particle Measuring Systems is to strive to meet or exceed the 
needs and expectations of our customers, and to align the activities of all employees 
with the common focus of customer satisfaction through continuous improvement in 
the quality of our products and services.

Environmental Information

This equipment must be properly disposed of at end-of-life by means of an 
authorized waste management system. Contact our Customer Response Center at 
(877) 475-3317 or (303) 443-7100 (International Tel1 3034437100) for 
dismantling and disposal information. 

Содержание Particle Measuring Systems LiQuilaz II E














































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды