manualshive.com logo in svg

Spectris Particle Measuring Systems LiQuilaz II E, Руководство по эксплуатации

Поделиться
Скачать
Spectris Particle Measuring Systems LiQuilaz II E Скачать руководство пользователя страница 28

LiQuilaz II E and S Operations Manual

Page 3-1

Chapter 3
Maintenance

This chapter is a basic maintenance guide for LiQuilaz II liquid particle counters. 

Occasional cleaning is required of the liquid capillary and it is the customer's 
responsibility to perform the cleaning when necessary. The need for capillary cleaning 
and the general health of the capillary can be improved by continuously running water 
through the system when not in use. In addition, the capillary should never be allowed 
to dry out, as this could permanently damage the capillary. 

The user can perform only the following maintenance: 

• Cleaning the capillary with the provided capillary cleaning kit

• Replacing fuses

• Replacing the tubing

Capillary Cleaning 

This section is a basic guide to capillary cleaning for LiQuilaz II sensor capillaries. 
Occasional cleaning is required of the liquid capillary and it is the customer's 
responsibility to perform the cleaning when necessary. 

The need for capillary cleaning and the general health of the capillary can be improved 
by continuously running water through the system when it is not in use. In addition, 
the capillary should never be allowed to dry out, as this could permanently damage 
the capillary.

Clean the capillary when the DC Light reading exceeds the recommended limits:

DC Light Specifications

 LiQuilaz II S liquid particle counter, model S02

< 0.5 Volts

 LiQuilaz II S liquid particle counter, model S03/S05

< 0.05 Volts

 LiQuilaz II E liquid particle counter, all models

> 7 Volts

A capillary cleaning kit is included with every LiQuilaz II sensor.

Содержание Particle Measuring Systems LiQuilaz II E














































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды