Spectris Particle Measuring Systems LiQuilaz II E Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 109

Spectris Particle Measuring Systems LiQuilaz II E Скачать руководство пользователя страница 87

Page E-4

LiQuilaz II E and S Operations Manual

Appendix E Configuring for Ethernet

Configuration Commands

?

Displays a command summary for the selected operational mode (a summary of the
information in this table).

Sta(tus)

Displays the following information:

•

Current firmware version number

•

MAC address

•

IP address

•

Multicast address

•

Net mask

•

Gateway

•

Queue size (applicable for PMS Ethernet and Modbus TCP connections)

Note

: The RS-485 has its own queue fixed to 10.

•

Connection status (if used with Facility Net)

•

Operational mode

Set ip aaa.bbb.ccc.ddd

The IP address is used when communicating across networks. This command sets the
address in the form of aaa.bbb.ccc.ddd. Each three-digit series is a value of 0–255,
separated by a period (

.

) character. An example of a valid IP address is

010.255.000.060

.

Set mas(k) aaa.bbb.ccc.ddd

Sets the network mask address using a decimal notation form of aaa.bbb.ccc.ddd.
Each three-digit series is a value of 0-255 separated by a period (.) character. The mask
separates the network address from the host address. This address is common to all
devices on the logical network. Usually the mask will be similar to 255.255.255.000.
Your network administrator will tell you if you need to enter this field.

Set mul(ticast) aaa.bbb.ccc.ddd

The multicast address must be set when using Facility Net. This command sets the
multicast address in a decimal notation form of aaa.bbb.ccc.ddd. Each three-digit
series is a value of 0-255 separated by a period (.) character. This address is unique to
the hardware it serves. An example of a valid multicast address is:

224.100.100.001

.

«
...
85
86
87
88
89
...
»

Содержание Particle Measuring Systems LiQuilaz II E














































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды