manualshive.com logo in svg

Spectris Particle Measuring Systems LiQuilaz II E, Руководство по эксплуатации

Поделиться
Скачать
Spectris Particle Measuring Systems LiQuilaz II E Скачать руководство пользователя страница 37

Page 3-10 

LiQuilaz II E and S Operations Manual

Chapter 3 Maintenance

Calibration

If you are using SamplerSight-Pharma as your user interface, you can calibrate the 
LiQuilaz II E20, LiQuilaz II E20P and LiQuilaz II E15P instruments. Refer to the 
Calibration chapter in the 

SamplerSight-Pharma User Guide

. 

Otherwise, contact Particle Measuring Systems Service. 

Fuses

The following procedure applies to all LiQuilaz II models. 

Required items:

• Small flat-bladed tool such as a small screw driver 

• Fuses: 250 V~, 5 x 20 mm, T, 0.75 A

>> To replace the fuses:

1.

Use the LiQuilaz II Liquid Particle Counter power switch (located where the power 
cable connects) to turn off power.

2.

Disconnect the power cable from the particle counter’s power entry module.

NOTE:

 

The black plastic assembly that the power cable connects to is called the 

power entry module

. The power entry module also contains the fuse tray. 

3.

Use a tool like a flat-bladed screwdriver to open the fuse tray on the power entry 
module. 

4.

Remove the old fuses. 

5.

Install the correct replacement fuses. 

6.

Replace the fuse receptacle covers. 

7.

Restore power.

WARNING

Disconnect the power cord from its power source.

Содержание Particle Measuring Systems LiQuilaz II E














































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды