manualshive.com logo in svg

Spectris Particle Measuring Systems LiQuilaz II E, Руководство по эксплуатации

Поделиться
Скачать
Spectris Particle Measuring Systems LiQuilaz II E Скачать руководство пользователя страница 102

Appendix G Serial Setup Command List

LiQuilaz II E and S Operations Manual

Page G-3

“set mod(e) n”

Set the Ethernet operational mode between PMS or Modbus.
If “n” is 0 then PMS, if “1” then Modbus. The unit will automatically 
reboot after the command.

“set mul(ticast) 
aaa.bbb.ccc.ddd”

Range Limits
0 – 255

Set Ethernet multicast address.
The values aaa.bbb.ccc.ddd represent decimal entries for each 
address octet. Do not use leading zeros. The multicast address is 
normally only used by Facility Net. This address must match the 
multicast address entered in Facility Net in order to have the full 
configuration utilities presented in the configuration dialog. This 
setting will be saved after the “write” command is issued.

“set ntp 
aaa.bbb.ccc.ddd”

Set Ethernet NTP (Network Time Protocol) address.
The values aaa.bbb.ccc.ddd represent decimal entries for each 
address octet. Do not use leading zeros. This setting will be saved 
after the “write” command is issued.

“set que(ue) n”

Set the data queue size for use in the PMS and Modbus Operational 
modes.
The value for “n” should be between 1 and 1440. The unit will 
automatically reboot after the command.

“set sam(ple) n”

Set sample interval into the unit.
The sample interval “n” needs to be a positive integer greater than 
or equal to 1 and less than or equal to 28800. The units are in 
seconds. The unit will stop sampling if this parameter is changed 
during a run state. This setting will be saved after the “write” 
command is issued.

“set serdump n”

Set the unit to dump serial data.
If “n” is 1 then serial dump is enabled, otherwise it is disabled. This 
setting will be saved after the “write” command is issued. Unlike 
the associated “data” command, this feature allows a method by 
which the unit can automatically dump data after boot. This 
feature is indicated in the status message if enabled.

“set telnet n”

Set the Telnet setting.
If “n” is 1 then the Telnet server is enabled, otherwise disabled. 
This can be used for security purposes, the Telnet server is enabled 
by default. This setting will be saved after the “write” command is 
issued.

“set inst(rument) float n”

Set the Modbus float register representation setting.
If “n” is 1 then the float representation is in effect, otherwise the 
integer representation is in effect. This setting will be saved after 
the “write” command is issued.

“set inst(rument) ntp n”

Set the NTP setting.
If “n” is 1 then the NTP client is enabled, otherwise disabled. This 
setting will be saved after the “write” command is issued.

“set inst(rument) retro n”

Set the retro mode.
If “n” is 1 then the retro mode is enabled, otherwise disabled. This 
setting will present the Family Name of “HSLIS” for use by versions 
of Facility Net prior to 4.0. This setting will be saved after the 
“write” command is issued.

Table

 

G-1    

Serial setup command list (Continued)

Command

Содержание Particle Measuring Systems LiQuilaz II E














































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды