Sourcetronic ST9201 Series Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 94

background image

◇

81

                                          Unit:

                              --Program data<set value>:
                                          Data format: float
                                          Set value: 0.1~1.0
                                          Resolution: 0.1
                                          Unit:

                              --Example:
                                          To set the OPEN rate for step 1 to 50%,
                                          :SOUR:SAFE:STEP 1:OS:OPEN 0.5.
                              --Example:

:SOUR:SAFE:STEP 1:OS:OPEN?
If the OPEN rate for step 1 is 50%,

0.5 is returned.

:

SOUR:SAFE:STEP:OSC:SHOR

                              Sets the SHORT rate for OS test.
                              Also inquires the SHORT rate.
                              --Syntax:
                                          Command message:      :

SOUR:SAFE:STEP <sn>:OSC:SHOR < set value >

                                          Query message:
                                                                  :SOUR:SAFE:STEP    <sn>:OSC:SHOR?
                                --Program data<sn>:
                                          Data format: Integer
                                          Set value: 1~49
                                          Resolution: 1
                                          Unit:

                              --Program data< set value >:
                                          Data format: Integer
                                          Set value: 0~5 (0 is OFF)
                                          Resolution: 1
                                          Unit:

                              --Example:
                                          To set the SHORT rate for step 1 to 200%,
                                          :SOUR:SAFE:STEP 1:OS:SHOR 2.
                              --Example:

:SOUR:SAFE:STEP 1:OS:SHOR?
If the SHORT rate for step 1 is 200%,

«
...
79
80
81
82
83
...
»

Содержание ST9201 Series































































































Отзывы:

Нет отзывов

Похожие инструкции для ST9201 Series

Бренд: Nemco Страницы: 13

Бренд: Ecco Страницы: 12

Бренд: UMF Medical Страницы: 12

Бренд: Taylor Страницы: 70

Бренд: Raith Страницы: 26

Бренд: Kane Страницы: 16

Бренд: Raytheon Страницы: 68

Бренд: KegLand Страницы: 23

Бренд: Hach Страницы: 456

Бренд: ZacUrate Страницы: 2

Бренд: ZacUrate Страницы: 2

Бренд: Gardenline Страницы: 24

Бренд: Analogue Solutions Страницы: 64

Power System KPS-US

Бренд: Keys Fitness Страницы: 8

Бренд: Torrent Страницы: 23

Бренд: Rottler Страницы: 96

Бренд: WIFO Страницы: 24

Бренд: Cutler-Hammer Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды