Sourcetronic ST9201 Series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 94

background image

◇

18

the place where DUT is connected with low terminal.

7.

SCAN interface

Be used to connect ST9121 multi-channel tester. SBOX control program is needed
to be customized.

8.

Backup interface

1.

IEEE488 (GPIB) parallel communication interface. (Option)

2.

ST10203 control interface (Option): it includes all functions of HANDLER
interface. In addition, 24V/1A DC power supply is addeded to connect the small
power-driven circuit, such as indicator light.

9.

Protective earth terminal

Be used to connect instrument to ground.

10.

RS232C serial interface

Serial communication, realize the communication with computer.

11.

Power jack

Be used to input AC power; please use the attached power line with fuse. Change

the fuse according to input power.

12.

Ground break-over calibration

Ground break-over resistance is 1 ohm, use potentiometer to calibrate if there is
deviation.

13.

Mark

This mark describes the instrument’s SN.

14.

High voltage output interface (optional)

Stand-by high voltage output interface.

3.3 Description

ST9201

Provide 5kVAC/30mA withstanding voltage, 6kVDC/10mA withstanding

voltage and insulation resistance tester.
ST9201S  Provide 5kVAC/30mA withstanding voltage, 6kVDC/10mA withstanding
voltage and insulation resistance with scanning test.
ST9201B  Provide 5kVAC/20mA withstanding voltage, 6kVDC/5mA withstanding
voltage and insulation resistance test.
ST9201C  Provide 5kVAC/20mA withstanding voltage test.

In high voltage modular, there is an AB power amplifier power which can assure

the programming of output voltage as well as the isolation of output voltage power
and line power. 40~600Hz high voltage transformer can rise voltage, and use high
voltage feedback loop to assure the accuracy of output voltage, then the actual
voltage adjustment rate is far smaller than that of transformer, which can be used
to the product whose VA is larger than the actual power.

In AC output, set the operation in 50 or 60Hz, not being limited by line voltage,

«
...
16
17
18
19
20
...
»

Содержание ST9201 Series































































































Отзывы:

Нет отзывов

Похожие инструкции для ST9201 Series

Бренд: York Fitness Страницы: 34

Бренд: Ecco Страницы: 2

Бренд: Landoll Страницы: 94

Бренд: Jacobs Ladder Страницы: 16

Бренд: Abbott Страницы: 2

FreeStyle Libre

Бренд: Abbott Страницы: 3

Бренд: abc Страницы: 8

Бренд: Cambro Страницы: 6

Бренд: KaVo Страницы: 49

Бренд: Easson Страницы: 33

Бренд: Garelick Страницы: 2

Бренд: Gardico Страницы: 2

Бренд: OceanSat Страницы: 85

Бренд: Ibiza Страницы: 21

Бренд: IBC Страницы: 8

Бренд: Ibanez Страницы: 8

Бренд: IAI Страницы: 5

Бренд: MAKSIWA Страницы: 155

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды