Sourcetronic ST9201 Series Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 94

background image

◇

79

                                          To set the TEST time for step 1 to 1,
                                          :SOUR:SAFE:STEP 1:IR:TIME:TEST 1.
                              --Example:

:SOUR:SAFE:STEP 1:IR:TIME:TEST?
If the current TEST time for step 1 is 1,

1 is returned.

:SOUR:SAFE:STEP:IR:AGC
Sets the AGC’s status for IR test.

Also inquires about the AGC’s status

                              --Syntax:
                                          Command message:
                                                                  SOUR:SAFE:STEP    <sn>:IR:AGC    <ON/OFF> or <1/0>
                                          Query message:
                                                                  SOUR:SAFE:STEP    <sn>:IR: AGC ?
                                --Program data<sn>:
                                          Data format: Integer
                                          Set value: 1~49
                                          Resolution: 1
                                          Unit:

                              --Program data<set value>:
                                          Data format: Character
                                          Set value: OFF(0), ON(1)
                                          Resolution:
                                          Unit:

                              --Example:
                                          To set the AGC’s status for step 1 to ON,
                                          :SOUR:SAFE:STEP :IR:AGC ON.
                              --Example:

:SOUR:SAFE:STEP :IR:AGC?
If the current AGC’s status for step 1 is ON,

ON is returned

:SOUR:SAFE:STEP:IR:CHAN
                              Sets HIGH/LOW/OPEN for the scanner channel for IR test.
                              Also inquires about the set value for the scanner channel.
                              --Syntax:
                                          Command message:
                                                                  SOUR:SAFE:STEP    <sn>:IR:CHAN      <channel>:

«
...
77
78
79
80
81
...
»

Содержание ST9201 Series































































































Отзывы:

Нет отзывов

Похожие инструкции для ST9201 Series

Бренд: Landoll Страницы: 52

Бренд: JBSYSTEMS Light Страницы: 14

Бренд: YardShape Страницы: 50

Бренд: GE Страницы: 138

Бренд: Landoll Страницы: 52

Бренд: Gason Страницы: 110

Бренд: Gainsborough Страницы: 2

Бренд: Backyard Discovery Страницы: 51

Бренд: Nautilus Страницы: 12

Бренд: CAIRE Страницы: 16

Бренд: Califone Страницы: 7

Бренд: CALITEK Страницы: 16

Бренд: LAHTI PRO Страницы: 20

Бренд: LAHTI PRO Страницы: 16

Бренд: J&M Страницы: 53

Бренд: Qazqa Страницы: 2

Бренд: Campbell Страницы: 2

Бренд: Raven Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды