9
Options
Chapt
er 1 Ov
e
rv
ie
w
Options
Input adaptors
The connector panel of the monitor is composed of the
connectors on the optional input adaptors installed in the
input option slots on the side panel of the monitor. Four or
eight adaptors can be installed.
The input signal type for each connector of the adaptor is
set with the Configurations tab window of the Main
Operation window, in accordance with the configuration
of the connector panel.
When installing the adaptor, be sure to perform the
necessary input setup in Input of the Configurations tab
window of the Main Operation window. If the setup is not
performed, the adaptors may not function correctly.
For information about the Configurations tab window of
the Main Operation window, see page 44.
For details of each input adaptor, refer to the operating
instructions of each model.
BKM-243HS HD/D1-SDI Input Adaptor
A decoder for serial digital component signals is built in
and the input/output connectors consist of two channels of
serial digital signal input and one channel of monitor
output.
• The signal from the MONITOR OUT connector of the
BKM-243HS does not satisfy the ON-LINE signal
specifications.
• For use of the MONITOR OUT connector in 2K/HD
Zoom mode, connect a coaxial cable less than 1 m (3.3
feet) long. For how to connect the cable, see page 23.
BKM-244CC HD/SD-SDI Closed Caption
Adaptor
A decoder for serial digital component signals is built in.
EIA/CEA-608 or EIA/CEA-708 standard closed caption
signals superimposed on the SDI signals are decoded and
displayed. Input/output connectors consist of two channels
of serial digital input and one channel of monitor output.
• The signal from the MONITOR OUT connector of the
BKM-244CC does not satisfy the ON-LINE signal
specifications.
• For use of the MONITOR OUT connector in 2K/HD
Zoom mode, connect a coaxial cable less than 1 m (3.3
feet) long. For how to connect the cable, see page 23.
BKM-250TG 3G/HD/SD-SDI Input Adaptor
A decoder for serial digital component signals is built in.
Time code and audio level of the embedded audio signals
superimposed on the SDI signals can be displayed. Input/
output connectors consist of two channels of serial digital
input and two channels of monitor output.
• The signal from the MONITOR OUT connector of the
BKM-250TG does not satisfy the ON-LINE signal
specifications.
• For use of the MONITOR OUT connector in 2K/HD
Zoom mode, connect a coaxial cable less than 1 m (3.3
feet) long. For how to connect the cable, see page 23.
When you install the following input adaptor to this
equipment, use that with the serial numbers given below.
• BKM-243HS with serial number 2108355 or higher
BKM-243HS: The equipment may not meet the
requirements of the electromagnetic interference standard
or work correctly, or you may not be satisfied with the
performance if designated input adaptors are not installed.
Input/Output Connector and Adaptor
By adding the optional input adaptors, the input/output
connector panel can be assembled in a wide variety of
configurations. Acceptable signals of each adaptor are
given in the following table. The type of signal to be
applied to each input/output connector is set with the
Configurations tab window of the Main Operation
window.
For information about the Configurations tab window of
the Main Operation window, see page 44.
a
: Signal can be reproduced.
a
(2): Two adaptors of the same model are used.
For details, see “Available Signal Formats” on page 95.
Note
Notes
Notes
Notes
Caution
Input adaptor BKM-243HS/
244CC
BKM-250TG
Input signal
Ser
ial dig
ita
l
inp
u
t
Single-link HD-SDI
a
a
Dual-link HD-SDI
a
(2)
a
Single-link 3G-SDI
a
Number of digital inputs
2
2
