Sony HD Super Motion HKCU1001, Руководство по установке

Страница: 20 / 102

1-14 (E)
. IM/HDCU1000 Series
Ref.No. Name Function Factory default setting
S405 V-DLY Video phase setting between HD and SD 0
Sets the phase difference (delay time) between the HD signal and the SD
signal output from CCU.
The phase can be advanced as follows based on the delay time set with S410.
HD standard: 128ck (27 MHz) increment
SD standard: 256ck (74 MHz) increment
S406 MODE1
1 MIC-GT 1&2/1,2 Sets whether or not to control MIC1 and MIC2 of the MIC GAIN CONTROL pin of the OFF
MIC REMOTE connector independently or by interlocking the MIC1 and MIC2 controls.
ON: MIC1, MIC2 independent control
MIC1 : 5 pin to 7 pin MIC2 : 12 pin to 14 pin
OFF: MIC1, MIC2 interlocked control MIC1, MIC2 : 5 pin to 7 pin
2 MIC-G7 STD/700 For switching the interface specification of MIC-Remote (D-SUB-15P) OFF
ON: Old interface (700 mode)
OFF: Standard-I/F
3 D-SUB MIC/WFM For switching the D-SUB-15P function on HDCU1500 OFF
ON: WFM-Remote
OFF: MIC-Remote
4 ASPECT RMT/PNL ON: Accepts the switching command last input from MSU when the ASPECT OFF
switching from outside (D-Sub) is valid.
OFF: Does not accept the command input from MSU when the ASPECT
switching from outside (D-Sub) is valid.
5 Not used
6 CNU/RM For setting the priority of remote device on HDCU1500 hen the OFF
Front-PNL-RM (RM-B750) is installed
ON: Front-PNL-RM has priority.
OFF: Device connected to the Rear-RM-CMD connector has priority.
7 RCP-PX ENB/DIS Sets the monitor selection control method for PIX OUT by RCP. OFF
ON : Only WF can be controlled from RCP.
OFF : Both PIX and WF can be controlled from RCP.
8 MONI-S M&R/RCP Sets the monitor selection control method for PIX/WF OUT. OFF
ON : Can only be controlled from RCP (PIX/WF 1 system). When there is
PIX/WF 2 system, it can be controlled from MSU.
OFF : Can be controlled from either MSU or RCP. (Latest priority)
S407 REFERENCE HD REFERENCE SD
Reference (advance amount Reference (advance amount
of SD) of HD)
0 0 0
1 _ 4.74 usec _ 3.45 u sec
2 _ 9.48 usec _ 6.70 u sec
3 _ 14.2 usec _ 10.3 u sec
4 _ 19.0 usec _ 13.8 u sec
5 _ 23.7 usec _ 17.2 u sec
6 _ 28.4 usec _ 20.7 u sec
7 _ 33.2 usec _ 24.1 u sec
8 _ 37.9 usec _ 27.6 u sec
9
_
42.7 usec
_
31.0
u
sec
A _ 47.7 usec _ 34.5 u sec
B _ 52.1 usec _ 37.9 u sec
C _ 56.9 usec _ 41.4 u sec
D
_
61.6 usec
_
44.8
u
sec
E _ 66.3 usec _ 48.3 u sec
F _ 71.1 usec _ 51.7 u sec
1H 525 : 63.5 u sec 1125-60i : 29.6 u sec 750-60P : 22.2 u sec
625 : 64.0 u sec 1125-50i : 35.6 u sec 750-50P : 26.7 u sec
1125-24 PsF : 37.0 u sec