SMC Networks LECSA Series Скачать руководство пользователя страница 42

Страница: 42 / 96

During Actuator Operation: <Signals which must be ON during actuator operation>

Set PD01 as 0C24. The following signals will automatically turn on when power supply turns on.

SON

Servo-on

OFF

：

Servo-off

：

Servo-on (operational)

LSP

Forward rotaion Stroke end
(normally closed contact)

OFF

：

Forward rotaion Stroke end

：

Forward rotaion Stroke end off (operational)

LSN

Reverse rotaion Stroke end
(normally closed contact)

OFF

：

Reverse rotaion Stroke end

：

Reverse rotaion Stroke end off (operational)

EM1

Forced stop
(normally closed contact)

OFF

：

Forced stop

：

Forced stop off (operational)

In positioning mode (point table), congifure the operation mode using automatic/manual selection

MD0.

The MD0 off selection will allow Jog operation and it will require an input reserved for MD0.

For Automatic MD0 please set PD01 as 0C25. Will also include MD0 automatic ON.

MD0

Automatic/manual selection

OFF: Manual Operation Mode



JOG operation available.

ON: Automatic Operation Mode



Home position return/positioning mode operation available.

* Enabling “Stroke end” (LSP, LSN) , “Forced stop” (EM1) and “Servo-on” (SON) Signals

①

Set to PD01 to 0C24 in the I/O tab.

②

Click on the "Single Axis Write" button.

③

Cycle the power off, then for the changed Parameters to be enabled.

* In this configuration, the stroke end

(LSP, LSN)

, forced stop

(EM1)

and servo-on

(SON)

signals will be ON

automatically when the power is turned ON.

①

②

Содержание LECSA Series

































































































Результаты поиска

Содержание LECSA Series

Отзывы:

Похожие инструкции для LECSA Series

Бренды по названию

Популярные бренды

SMC Networks LECSA Series, Руководство по эксплуатации

Результаты поиска

Содержание LECSA Series

Отзывы:

Похожие инструкции для LECSA Series

Бренды по названию

Популярные бренды