SMC Networks LECSA Series Скачать руководство пользователя страница 12

Страница: 12 / 96

(2) Input signal

Position control mode: P, Speed control mode: S, Torque control mode: T, Point table method: CP, Program
method: CL

●

: Automatic ON can be set,

○

: Initial setting,

□

: Assignment is available with parameter,

－

: Assignment is not available

Symbol

Device name

Automatic

CP/

Function

Forward rotation

pulse train

○

In the open collector system
(max. input frequency 200kpps)
Forward rotation pulse train across PP-DOCOM
Reverse rotation pulse train across NP-DOCOM

It supports only to the sink (NPN) type interface.
It does not correspond to the source (PNP) type
interface.

Reverse rotation

pulse train

○

Differential

forward rotation

pulse train

○

In the differential receiver system
(max. input frequency 1Mpps)
Forward rotation pulse train across PG-PP
Reverse rotation pulse train across NG-NP

Differential

reverse rotation

pulse train

○

SON

Servo-on

●

○

Operation is available when SON is turned ON.

RES

Reset

○

□

Alarm can be reset.

LSP

Forward rotation

stroke end

●

○

□

Turn this signal on before operation. When this
signal turns off, the product is stopped suddenly
and servo lock is enabled.

LSN

Reverse rotation

stroke end

●

○

□

Turn this signal on before operation. When this
signal turns off, the product is stopped suddenly
and servo lock is enabled.

TL1

Internal torque

limit selection

□

When this signal turns on, the torque will be
lower than the set parameter torque.

ST1

Forward rotation

start

○

Start the servo motor.

ST2

Reverse rotation

start

○

Start the servo motor.

RS1

Forward rotation

selection

○

Servo motor torque generating direction is
selected.

RS2

Reverse rotation

selection

○

Servo motor torque generating direction is
selected.

SP1

Speed selection 1

○

The command rotation speed during operation is
selected.

SP2

Speed selection 2

□

SP3

Speed selection 3

□

EM1

Forced stop

●

○

When this signal turns on, forced stop can be
released.

Clear

○

When CR is turned on, the droop pulses of the
position control counter are cleared on its
leading edge.

DI0

Point table No/

Program No.

selection 1

●

○

Select point table, program and return to home
position mode with DI0 to DI2.

DI1

Point table No/

Program No

selection 2

●

○

DI2

Point table No/

Program No

selection 3

●

□

MD0

Automatic/manual

selection

●

○

When  this  signal  turns  on,  automatic  operation
mode  is  activated.  When  this  signal  turns  off,
manual operation mode is activated.

Содержание LECSA Series

































































































Результаты поиска

Содержание LECSA Series

Отзывы:

Похожие инструкции для LECSA Series

Бренды по названию

Популярные бренды

SMC Networks LECSA Series, Руководство по эксплуатации

Результаты поиска

Содержание LECSA Series

Отзывы:

Похожие инструкции для LECSA Series

Бренды по названию

Популярные бренды