SMC Networks LECSA Series Скачать руководство пользователя страница 13

Страница: 13 / 96

(3) Output signal

Position control mode: P, Speed control mode: S, Torque control mode: T, Point table method: CP, Program
method: CL

○

: Initial setting,

□

: Assignment is available with parameter,

－

: Assignment is not available

Symbol

Device name

CP/

Function

ALM

Trouble

○

This signal turns off while alarm is generated.

Ready

○

When servo-on turns on and operation is available, this
signal turns on.

INP

In-position

○

This signal turns on when the droop pulse is within the
setting range.

Speed reached

○

When the servo motor rotation speed reaches the set
speed, this signal turns on.

VLC

Limiting speed

□

This signal turns on when reaching the speed restricted by
parameter.

TLC

Limiting torque

□

This signal turns on when reaching the torque set by
parameter while torque is generated. .

ZSP

Zero speed

□

When the servo motor rotation speed is lower than the
speed set by parameter, this signal turns on.

MBR

Electromagnetic

brake interlock

○

This signal turns off in case of servo off or when alarm is
generated.

Содержание LECSA Series

































































































Результаты поиска

Содержание LECSA Series

Отзывы:

Похожие инструкции для LECSA Series

Бренды по названию

Популярные бренды

SMC Networks LECSA Series, Руководство по эксплуатации

Результаты поиска

Содержание LECSA Series

Отзывы:

Похожие инструкции для LECSA Series

Бренды по названию

Популярные бренды