SMC Networks LECSA Series Скачать руководство пользователя страница 83

Страница: 83 / 96

(2) Timing chart

Forward
rotation

0r/min

OFF

Automatic/manual
selection (MD0)

OFF

Travel completion
(MEND)

OFF

Rough match (CPO)

Servo motor
speed

Acceleration time
constant parameter
No. PE07

Home position return
speed parameter No. PE04

Home position
address parameter
No. PE 08

3ms or less

OFF

6ms or more

Forward rotation start
(ST1)

OFF

Reverse rotation start
(ST2)

Stopper time
parameter No. PE10

OFF

Limiting torque (TLC)

Parameter No. PC14

(Note 3) Parameter No. PE 11

Parameter No. PC14

Torque limit value

(Note 4)

DI0, DI1, and DI2

OFF

Home position return
completion (ZP)

Stopper

(Note 1)

6ms or more

(Note 2)

Note 1. External input signal detection is delayed by the input filter setting time of parameter No. PD19. Implement a sequence that changes DI0,

DI1 and DI2 ahead of time by considering delays in output signal sequence from the PC or PLC and variations of a signal change due to

hardware.

2. TLC turns ON when the torque reaches the value set in forward torque limit (parameter No. PA11),reverse torque limit (parameter No.

PA12) or internal torque limit (parameter No. PC14).

3. The torque limit that is enabled at this point is as follows.

(Note)

Input device

Limit value status

Validated torque limit values

TL1

Parameter No. PE11

Parameter No. PC14

Parameter No. PE11

Parameter No. PC14

Parameter No. PE11

Parameter No. PC14

Note. 0: off

1: on

4. Point table method: Select the home position return mode by turning OFF DI0, DI1 and DI2.

Program method: Select the program that has the home position return "ZRT" command.

The set value in parameter No. PE08 (home position return position data) is applied as position address at the time of

the home position return being completed.

OFF

Forward rotation
stroke end

(LSP)

Reverse rotation
stroke end (LSN)

Forced stop (EM1)

OFF

Содержание LECSA Series

































































































Результаты поиска

Содержание LECSA Series

Отзывы:

Похожие инструкции для LECSA Series

Бренды по названию

Популярные бренды

SMC Networks LECSA Series, Руководство по эксплуатации

Результаты поиска

Содержание LECSA Series

Отзывы:

Похожие инструкции для LECSA Series

Бренды по названию

Популярные бренды