SMC Networks LECSA Series Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 96

SMC Networks LECSA Series Скачать руководство пользователя страница 80

-

78

-

No.

Name

Function

Indication

range

Unit

5

Command pulse
frequency

The frequency of the position command input pulses is
displayed.
Reverse rotation is indicated by a minus (-) sign.
(Note)  -1500  to  1500  kpulse/s  is  showed  when
inputting command pulse.
Pulse  unit  of  encoder  is  displayed  during  test
operation.

-999999999 to

999999999

pulse

6

Regenerative load
ratio

The  ratio  of  regenerative  power  to  permissible
regenerative power is displayed in %.
As  the  permissible  regenerative  power  depends  on
whether there is the regenerative brake option or not.
Set  Parameter  PA02  correctly  according  to  the
regenerative option.
The guideline is 80% or less.

0 to 100

%

7

Effective load ratio

The continuous effective load torque is displayed.
The effective value is displayed relative to the rated
torque of 100%.

0 to 300

%

8

Peak load ratio

The maximum torque is displayed.
The highest value in the past 15 seconds is displayed
relative to the rated torque of 100%.

0 to 400

%

9

Instantaneous
torque

Torque that occurred instantaneously is displayed.
The value of the torque that occurred is displayed in
real time relative to the rated torque of 100%.

0 to 400

%

10

Within
one-revolution
position

Position within one revolution is displayed in encoder
pulses.
The value returns to 0 when it exceeds the maximum
number of pulses.

0 to 262143

pulse

11

Load inertia
moment ratio

The estimated ratio of the servo motor axis converted
inertia moment to the servo motor inertia moment is
displayed.

0.0 to 300.0

times

12

Bus voltage

5: Overvoltage (About 400V or more)
4: High voltage (About 375V or more)
3: Normal
2: Low voltage (About 200V or less)
1: Undervoltage (About 160V or less)

Refer to the

function on the

left side.

-

13

Current position

The actual current position where the machine home
position is assumed as zero is displayed.

-999999 to

999999

× 10STM

μm

14

Command position

Point table, position data within the program, and the
command position being set are displayed.

-999999 to

999999

× 10STM

μm

15

Remaining
command distance

The command remaining distance of the currently
selected point table is displayed.

0 to

999999

× 10STM

μm

16

Point
table/Program No.

The point table No./program No. which is being
performed is displayed.
Display range: Point table No. 0 to 7/Program No. 0 to
8

Refer to the

function on the

left side.

-

17

Step No.

The step No. of program which is being performed is
displayed.

0 to 120

-

18

Settling time

The settling time is displayed.

0 to 999

ms

19

Oscillation
detection
frequency

The frequency at oscillation detection is displayed.

100 to 4500

Hz

20

Tough drive times

The times moving to the tough drive are displayed.

0 to 99

times

«
...
78
79
80
81
82
...
»

Содержание LECSA Series

































































































Отзывы:

Нет отзывов