SMC Networks LECSA Series Скачать руководство пользователя страница 54

Страница: 54 / 96

5.6.2 Motorspeed Configuration

<Rotation Speed Configuration>

①

Motorspeed (r/min) configuration.

*r/min (rpm): Indicated motor rotation speed (motor rotations/min)

Rotation speed must be between 0 and the allowable speed limit for each actuator. Please be aware that the
actuator will not operate if this is set to 0.

If the rotation speed is too low, this may cause vibration; check the actuator while changing settings.

Movement speed (mm/s) must be converted into rotation speed (r/min).
See below for the conversion formula.

Calculating motor speed conversion example using an actuator with a 20mm lead and 500 [mm/sec]
speed.

Rotation Speed (rpm) = Speed (mm/s)

Lead (mm) }×60 (S)

{500 (mm/s) ÷20 (mm) }×60 (s) =1500 (rpm)

Distance of movement per second

Distance of movement per rotation

Rotations per Second

①

Содержание LECSA Series

































































































Результаты поиска

Содержание LECSA Series

Отзывы:

Похожие инструкции для LECSA Series

Бренды по названию

Популярные бренды

SMC Networks LECSA Series, Руководство по эксплуатации

Результаты поиска

Содержание LECSA Series

Отзывы:

Похожие инструкции для LECSA Series

Бренды по названию

Популярные бренды