SKYLUX Climax 36178 Скачать руководство пользователя страница 27

Страница: 27 / 88

20/11/2020

27/88

E_MH_Installation_instructions_Skylux_Climax

Gutter

Multiple gutter elements can be connected to each other for gutter lengths > 7 metres. A gutter support must be

installed at every gutter connection point. We recommend tilting the profiles and supporting the gutter support

connections when using a gutter and gutter support (GD1.GD2) combination.

The gutter profiles can be linked using connection pins 909 and/or connector profile GI.

Use silicone glue SG20 as sealant.

A raised profile GR can be installed on the gutter G. Position

the side gutter slide ends first and subsequently fasten the

GR profile on to the gutter every 500 mm.

The gutter slide ends must be pre-installed using self-drilling

ZGS screws if the gutter is installed between two walls (for

example with a gutter bracket).

Place the pre-assembled gutter on the posts and fasten the

structure using coated ZSG screws.

SG20

909

Install the outlet in the gutter opening and seal

using silicone.

G + GI + SG20 + 909 (3x)

ZSG (4x)

GDC

ZSG

500

Содержание Climax 36178

























































































Результаты поиска

Содержание Climax 36178

Отзывы:

Похожие инструкции для Climax 36178

Бренды по названию

Популярные бренды

SKYLUX Climax 36178, Руководство по установке

Результаты поиска

Содержание Climax 36178

Отзывы:

Похожие инструкции для Climax 36178

Бренды по названию

Популярные бренды