SKYLUX Climax 36178 Скачать руководство пользователя страница 82

Страница: 82 / 88

E_MH_Installation_instructions_Skylux_Climax

20/11/2020

82/88

Glass thickness

GVB

GVT

Y16P (ABS)

Y10 (alu)

GSP

(blocks)

Adhesive SG20

8 – 21 mm

2 x

GSP 8

22 - 29 mm

1 x

GSP 20

30 - 34 mm

1 x

GSP 20

Specific installation tips for glazing connections

Application:

The glass connector is used for slanted roofs to create a watertight connection between two glass or two plastic

sheet sections. This is only possible with sheet support TP or TPG and the screw-in type clips CLSB with CLST/CLSL.

The following parts are used for a glass connection:

GVT top profile

Y16P thermal bridge

GSP 20 or GSP 8 buffer blocks

Bottom profile GVB

Adaptor profile Y10

Glass adhesive SG20

Assembly in relation to the glazing thickness:

For glazing 8 – 21 mm GVT + GVT (single glazing)

For double glazing or plastic sheets > 21 mm (GVB + GVT + Y16P + Y10)

Measurement and preparation:

GVT

GSP8

SG20

27 mm

tot

Glazing length:
Ltot = L1 + 27 mm + L2

Ltot = total length of glazing

L1 = length of the bottom glass sheet

L2 = length of the top glass sheet

GVT

GSP20

GVB Y16P GSP20

SG20

tot

27 mm

GSP20

GVB

Y16P

GVT

Y10

GSP20

SG20

60mm

TPG

S38.3

SG20

- 12mm

60mm

S1 / S2

B =

AX - 22 mm

GVB

Y16P

GVT

Cut profiles GVT, GVB, L632, Y16P and/or Y10 using

the same width B as for the glass sheet. Ensure that

surfaces to be glued are sufficiently dry and free from

dust and grease.

Measure the length L1 - 12 mm from glass stopper S38.3

and draw a line on the ribbed coex layer of sheet support

TPG. Draw a second line 60 mm further along. Remove

only the coex layer between both drawn lines Add SG20

adhesive to the zones without a coex layer.

Содержание Climax 36178

























































































Результаты поиска

Содержание Climax 36178

Отзывы:

Похожие инструкции для Climax 36178

Бренды по названию

Популярные бренды

SKYLUX Climax 36178, Руководство по установке

Результаты поиска

Содержание Climax 36178

Отзывы:

Похожие инструкции для Climax 36178

Бренды по названию

Популярные бренды