SKYLUX Climax 36178 Скачать руководство пользователя страница 83

Страница: 83 / 88

20/11/2020

83/88

E_MH_Installation_instructions_Skylux_Climax

Specific installation tips for glazing connections

Installation:

Add adhesive to the ribbed zone of bottom profile GVT

and position the profile as indicated. Press the profile

evenly and ensure there is counterpressure along the

bottom side. Remove excess adhesive and silicone

sealant.

Install seals C8 in screw-in type clips CLSB. Drill holes

with a Ø of 5.5 mm every 50 cm, starting and ending

at 20 cm from the ends. Fasten profile CLSB to sheet

support TPG using adapted Hi-Lo screws. Press the clips

(CLST/CLSL) manually or using a rubber hammer.

Y16P

GVB

Y16P

GVB

Y10

SG20

Slide profiles Y16P and Y10 in bottom profile GVB in

relation to the glazing thickness according to the table

on page 80. The GVT profile is also used as the bottom

profile without spacers for single glazing (8, 10 and 12

mm) or glazing up to 21 mm.

Position the complete set on sheet support TPG with

the stop shoulder towards the ridge. Add adhesive to the

bottom ribbed zone of bottom profile GVB (or GVT).

L432 /

L632

SG20

L432 / L632

Stick end profile L432 or L632 on to the glazing. Position

the bottom glass sheet on the conservatory supports.

Press profile GVB against the glazing. Position 2 plastic

buffer blocks in-between the glazing and bottom profile

GVB. Repeat this for all supports.

Add adhesive to the top ribbed zone of bottom profile

GVB. Position the top glass sheet and add 2 plastic buffer

blocks in-between the glass sheet and the stop shoulder

without any clearance.

SG20

SG2

CLST

GVT

CLSB

Hilo 25/42

Содержание Climax 36178

























































































Результаты поиска

Содержание Climax 36178

Отзывы:

Похожие инструкции для Climax 36178

Бренды по названию

Популярные бренды

SKYLUX Climax 36178, Руководство по установке

Результаты поиска

Содержание Climax 36178

Отзывы:

Похожие инструкции для Climax 36178

Бренды по названию

Популярные бренды