SKYLUX Climax 36178 Скачать руководство пользователя страница 38

Страница: 38 / 88

E_MH_Installation_instructions_Skylux_Climax

20/11/2020

38/88

Finish

SIDE SUPPORTS

SEAL FINISH

Seal C2CX for plastic sheets or glass: The glazing thickness and options are provided on page 84.

Push seal C2CX into sheet support TP(G) or into raised profile Y25/Y32. Cut side finishing profile L16P obliquely

on the wall side in accordance with the roof pitch a. Measure the distance from the wall to the stop profile to

determine the length of profile L16P. Position profile L16P against the exterior against the support profile. Fasten

profile L16P every metre sideways against the support (with ZSG) or against the wall using screws if the structure is

to be freestanding or against a wall.

CLIP FINISH

Clips for plastic sheets or glass: The glazing thickness and options are provided on page 84.

CLSB + CLSL for plastic sheets or glass with a

thickness of 8 to 34 mm: Position seal C8 or CY10 on

one side into the clips.

CLL for plastic sheets or glass with a 16, 25 or 32 mm

thickness: Position seal C8 or CY10 on one side into

the clips.

TP(G)

C2CX

L16P

ZSG

5 mm

C2CX

Y25/Y32

TP(G)

L16P

CLL

CLSL

CLSB

Hilo 25/42

Содержание Climax 36178

























































































Результаты поиска

Содержание Climax 36178

Отзывы:

Похожие инструкции для Climax 36178

Бренды по названию

Популярные бренды

SKYLUX Climax 36178, Руководство по установке

Результаты поиска

Содержание Climax 36178

Отзывы:

Похожие инструкции для Climax 36178

Бренды по названию

Популярные бренды