SKYLUX Climax 36178 Скачать руководство пользователя страница 48

Страница: 48 / 88

E_MH_Installation_instructions_Skylux_Climax

20/11/2020

48/88

Gutter

Multiple gutter elements can be connected to each other for gutter lengths > 7 metres. A gutter support must be

installed at every gutter connection point. We recommend tilting the profiles and supporting the gutter support

connections when using a gutter and gutter support (GD1.GD2) combination.

The gutter profiles can be linked using connection pins (909) and/or GI connector profile. Use silicone glue SG20

as sealant.

Install the outlet in the gutter opening and seal using

silicone.

The gutter slide ends have to be pre-installed using

self-drilling ZGS screws if the gutter is installed

between two walls (for example with a gutter

bracket).

G + GI + SG20 + 909 (3x)

G + 909 (3x)

909

SG20

ZSG (4x)

GDC

Place the preassembled gutter on the posts and

fasten the structure using coated ZSG screws.

A raised profile GR can be installed on the G

gutter. First, position the side gutter slide ends

and, next, fasten the GR profile on to the gutter

every 500 mm.

500

Содержание Climax 36178

























































































Результаты поиска

Содержание Climax 36178

Отзывы:

Похожие инструкции для Climax 36178

Бренды по названию

Популярные бренды

SKYLUX Climax 36178, Руководство по установке

Результаты поиска

Содержание Climax 36178

Отзывы:

Похожие инструкции для Climax 36178

Бренды по названию

Популярные бренды