Skoda Rapid NH 2014 страница 119 Скачать руководство пользователя

Страница: 119 / 319

– Pull the door window - 1 - upwards at an angle - arrows - to‐

wards the outside of the vehicle and out of the window chan‐

nel.

2.11.2

Installing

Note

Before inserting the expanding dowel - 3 - and the expanding pin

- 4 -, check the door window - 1 - for damage.

– Take the mean of the centre straddling dowel - 3 - and insert

it when the door window is removed - 1 -.

– Press the straddle pin -4- into the straddling dowel -3-.
– Guide the pane - 1 - into the door - 2 - - arrows a - and insert

the window lifter guide - 5 -.

– Gently tap on the pane - 1 - to lock it from above into the win‐

dow lifter - 5 -.

– It must be pressed until the catch locks audibly into place.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

2. Door internal parts

111

Содержание Rapid NH 2014
































































































































































































































































































































Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды

Skoda Rapid NH 2014, Руководство по ремонту

Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды