manualshive.com logo in svg

Skoda Rapid NH 2014, Руководство по ремонту


Поделиться
Скачать
background image

Installing

Note

The ambient temperature must be above 18°C during the gluing

procedure of the spoiler!

– Thoroughly clean the adhesive surfaces e.g. with cleaning

solution D 009 401 04.

– Apply glass/paint primer D 181 650 A1 to the adhesive surfa‐

ces of the spoiler and let them dry off.

– Apply glue sealing material D 172 090 A2 into the guiding

groove in the spoiler.

– Stick on the spoiler within 15 minutes after applying the glue

sealing material!

– Partially unglue the protective foil from the adhesive tape on

the edges.

– Position the spoiler evenly onto the tailgate.
– Maintain an even gap.
– Remove the protective foil from the adhesive tape.
– Press the spoiler evenly onto the tailgate.
– Secure spoiler against moving with adhesive tape.

Note

♦

The glue sealing material must dry for at least 2 hours. Do not

drive the vehicle in this time.

♦

Do not drive through the carwash within 24 hours of gluing on

the spoiler.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

192

     Rep. gr.66 - Exterior equipment

Содержание Rapid NH 2014
































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rapid NH 2014

APS Auto Parts Specialist iBoard IB-ZK406 Installation Instructions preview
iBoard IB-ZK406
Бренд: APS Auto Parts Specialist Страницы: 3
DAVIS 8126GD User Manual preview
8126GD
Бренд: DAVIS Страницы: 32
Rightline Gear Car Top Duffle Bag Setup Manual preview
Car Top Duffle Bag
Бренд: Rightline Gear Страницы: 2
Axxess AXGMLN-08 Installation Instructions Manual preview
AXGMLN-08
Бренд: Axxess Страницы: 8
Webasto Transit Vancouver Wagon Manual preview
Transit Vancouver Wagon
Бренд: Webasto Страницы: 44
Ecco Vantage 12 Series Installation And Operation Instructions preview
Vantage 12 Series
Бренд: Ecco Страницы: 5
UAZ UAZ-374195 Operating Manual preview
UAZ-374195
Бренд: UAZ Страницы: 90
RHOX LGT-381L Installation Instructions Manual preview
LGT-381L
Бренд: RHOX Страницы: 8
BMW 51 47 0 027 792 Installation Instructions Manual preview
51 47 0 027 792
Бренд: BMW Страницы: 7
Ford 2007 Navigator (Spanish) Owner'S Manual preview
2007 Navigator
Бренд: Ford Страницы: 728
Westin 58-53935 Installation Instructions preview
58-53935
Бренд: Westin Страницы: 5
Waeco Magic Watch MWE-850-4DSM Installation And Operating Manual preview
Magic Watch MWE-850-4DSM
Бренд: Waeco Страницы: 204
Kia OPTIA hybrid 2020 Features & Functions Manual preview
OPTIA hybrid 2020
Бренд: Kia Страницы: 54
Vauxhall 2013 Ampera Infotainment Manual preview
2013 Ampera
Бренд: Vauxhall Страницы: 95
TATA Motors Harrier 2021 Owner'S Manual preview
Harrier 2021
Бренд: TATA Motors Страницы: 308
PUTCO 1951 Series Instruction Manual preview
1951 Series
Бренд: PUTCO Страницы: 3
Havis-Shields Telescoping Computer Base C-TCB-34 Install Instructions preview
Telescoping Computer Base C-TCB-34
Бренд: Havis-Shields Страницы: 1
PEUGEOT 106 2001 Owner'S Manual preview
106 2001
Бренд: PEUGEOT Страницы: 107

Бренды по названию

Популярные бренды

Загрузить еще бренды