manualshive.com logo in svg

Skoda Rapid NH 2014, Руководство по ремонту


Поделиться
Скачать
background image

1.12

Preparing the new window for fitting

1.12.1

Cut back the adhesive bead

Carry out the following tasks

Note

♦

Cut back the remaining glue sealing material to 1-2 mm just

prior to adhering again. While doing so, do not damage the

glass/primer and ceramic layer.

♦

The remainder of the sealing compound serves as a base for

the newly applied adhesive sealant.

WARNING

Do not prime the adhesive surface and do not treat with clean‐

ing solution. Keep the adhesive surfaces free of dirt or grease.

Exception: If the bonding is not carried out immediately after cut‐

ting back, the sealing compound must be activated with the

activator.

1.12.2

Prepare new window for fitting

Carry out the following tasks
All the windows are not pre-layered as a spare part.

Note

♦

The area where the adhesive bead is applied is neither pre-

layered nor primed.

♦

The sealing lip is a component part of a new windscreen.

– Clean edge of the window (where glass/paint primer will be

applied) up to a width of approx. 20 mm with cleaning solution.

– Next, wipe off the edge of the window (where glass/paint pri‐

mer will be applied) using a dry, lint-free cloth not contamina‐

ted with any substances.

WARNING

The ceramic layer on the window is no glass/paint primer! It is

absolutely essential to prime it before applying the sealing ma‐

terial! Only use glass/paint primer D 009 200 02!

– Now apply the glass/paint primer with the applicator uniformly

in one go.

♦ Minimum hardening time approx. 10 minutes.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

154

     Rep. gr.64 - Glazing

Содержание Rapid NH 2014
































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rapid NH 2014

Jeep Compass Overview Manual preview
Compass
Бренд: Jeep Страницы: 25
Mercedes-Benz 2016 SLK Operator'S Manual preview
2016 SLK
Бренд: Mercedes-Benz Страницы: 358
Nav TV Ford 4” UNI-CAM Manual preview
Ford 4” UNI-CAM
Бренд: Nav TV Страницы: 6
Saab 2007 9-3 Remote Starter Owner'S Manual preview
2007 9-3 Remote Starter
Бренд: Saab Страницы: 304
Road Ranger H392 Installation Manual preview
H392
Бренд: Road Ranger Страницы: 22
Omix-Ada 11704.05 Owner'S Manual preview
11704.05
Бренд: Omix-Ada Страницы: 6
Magneti Marelli 350203061230 Installation Instruction preview
350203061230
Бренд: Magneti Marelli Страницы: 2
Rugged Ridge 11252.51 Installation Instructions preview
11252.51
Бренд: Rugged Ridge Страницы: 3
E&G Classics Black Ice Mesh Instruction Manual preview
Black Ice Mesh
Бренд: E&G Classics Страницы: 4
Veldo Teknoloji DUCATO Manual preview
DUCATO
Бренд: Veldo Teknoloji Страницы: 32
Tesla MODEL Y Owner'S Manual preview
MODEL Y
Бренд: Tesla Страницы: 274
Hummer HX-T Owner'S Manual preview
HX-T
Бренд: Hummer Страницы: 31
RAM Truck 2014 Owner'S Manual preview
Truck 2014
Бренд: RAM Страницы: 330
Dodge CHALLENGER HELLCAT 2017 Owner'S Manual preview
CHALLENGER HELLCAT 2017
Бренд: Dodge Страницы: 484
Mercedes-Benz W211 Manual preview
W211
Бренд: Mercedes-Benz Страницы: 27
Chrysler Sebring Convertible Owner'S Manual preview
Sebring Convertible
Бренд: Chrysler Страницы: 454
Federal Signal Corporation Cuda TriOptic 351014F Series Instruction Sheet preview
Cuda TriOptic 351014F Series
Бренд: Federal Signal Corporation Страницы: 4
Kia Magentis 2002 Owner'S Manual preview
Magentis 2002
Бренд: Kia Страницы: 216

Бренды по названию

Популярные бренды

Загрузить еще бренды