manualshive.com logo in svg

Skoda Rapid NH 2014, Руководство по ремонту


Поделиться
Скачать
background image

Install the rear spoiler

Note

The ambient temperature must be above 18°C during the gluing procedure of the spoiler!

– Thoroughly clean the adhesive surfaces e.g. with cleaning

solution D 009 401 04.

– Apply glue sealing material D 172 090 A2 into the guiding

groove (Pos. 2) in the spoiler.

– Stick on the spoiler within 15 minutes after applying the glue

sealing material!

– Partially unglue the protective foil from the adhesive tape on

the edges.

– Position the spoiler evenly onto the tailgate.
– Maintain an equal gap of 2 mm from the side tailgate edge.
– Remove the protective foil from the adhesive tape.
– Press the spoiler evenly onto the tailgate.
– Secure spoiler against moving with adhesive tape.

Note

♦

The adhesive cement must dry for 2 hours. Do not drive the vehicle in this time.

♦

Do not drive into the carwash within 24 hours of gluing on the spoiler.

4.2

Rear spoiler - Spaceback

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

190

     Rep. gr.66 - Exterior equipment

Содержание Rapid NH 2014
































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rapid NH 2014

J-Top COMPACT Instructions preview
COMPACT
Бренд: J-Top Страницы: 2
GARO TWIN+ Assembly Instructions / End User Instruction preview
TWIN+
Бренд: GARO Страницы: 23
GARO LS4 Wallmounted Operational Instructions preview
LS4 Wallmounted
Бренд: GARO Страницы: 15
Jeda Wireless Pad Manual preview
Wireless Pad
Бренд: Jeda Страницы: 8
Jeep 2009 Wrangler Owner'S Manual preview
2009 Wrangler
Бренд: Jeep Страницы: 496
LAS BC260 Operating Instructions Manual preview
BC260
Бренд: LAS Страницы: 44
LAS 11807 Operating Instructions Manual preview
11807
Бренд: LAS Страницы: 24
Vauxhall MOVANO Owner'S Manual preview
MOVANO
Бренд: Vauxhall Страницы: 177
Axxess AX-DSPX-HYKIA2 Installation Instructions preview
AX-DSPX-HYKIA2
Бренд: Axxess Страницы: 4
Vintage Air 473275 Manual preview
473275
Бренд: Vintage Air Страницы: 14
Victory 4x4 UNI-UPRS Install Instructions Manual preview
UNI-UPRS
Бренд: Victory 4x4 Страницы: 13
GMC Chevrolet Silverado 2500HD 2021 Owner'S Manual preview
Chevrolet Silverado 2500HD 2021
Бренд: GMC Страницы: 433
Cadillac Escalade ESV 2014 Owner'S Manual preview
Escalade ESV 2014
Бренд: Cadillac Страницы: 508
Hama Liberty III Quick Start Manual preview
Liberty III
Бренд: Hama Страницы: 2
H&S XRT Pro Installation & Operation Manual preview
XRT Pro
Бренд: H&S Страницы: 32
WATT CARWATT CV12-220C150 User Manual preview
CARWATT CV12-220C150
Бренд: WATT Страницы: 26
Audi Audi 80 1987 Workshop Manual preview
Audi 80 1987
Бренд: Audi Страницы: 63
DEFA MultiCharger 1204 User'S Installation Manual preview
MultiCharger 1204
Бренд: DEFA Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды