Skoda Rapid NH 2014 Скачать руководство пользователя

Страница: 153 / 319

– The moulded headliner can now be lowered sufficiently so that

the windscreen can be cut out without damaging the moulded

headliner.

– Remove the plenum chamber cover

⇒ “1.8 Plenum chamber cover”, page 13

– Slide the cover foil - 1 - between the windscreen and the dash

panel.

– Pull the end of the cutting thread - 2 - through the sealing ma‐

terial into the vehicle interior using the awl.

– Secure the end of the cutting thread with clip - 3 - against pull‐

ing out.

– Insert the cutting thread - 2 - with the help of the pipe - 1 - into

the window frame.

– Lay the cutting thread around the windscreen.
– Ensure that the cutting thread is laid at the corners under the

windscreen.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

1. Glued windows

145

Содержание Rapid NH 2014
































































































































































































































































































































Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды

Skoda Rapid NH 2014, Руководство по ремонту

Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды