Skoda Rapid NH 2014 Скачать руководство пользователя

Страница: 241 / 319

1 - Steering wheel
Removing

– Remove driver's airbag

unit

⇒ Item 3 (page 233)

– Position the steering

wheel to centre position

(wheels in straighta‐

head position).

– Unscrew screw -2-.

– Mark the opposite posi‐

tion of the steering

wheel and the shaft -4-

with a line, as long as

this position is not facto‐

ry-marked.

– Remove the steering

wheel from the steering

column.

Installing

– The installation occurs

in reverse order.

2 - 30 Nm + 90°.

– Can be used up to five

times, then replace.

– Mark with a dot after

each mounting.

3 - Airbag unit

– Removing and installing

⇒ “3.13 Removing and installing driver airbag unit”, page 233

4 - Steering wheel shaft

3.13

Removing and installing driver airbag

unit

WARNING

Observe the general safety instructions for working on airbag,

belt tensioner and battery separation units (pyrotechnical com‐

ponents)

⇒ “3.3 Observe the general safety instructions for working on

airbag, belt tensioner and battery separation units (pyrotech‐

nical components)”, page 225

Observe the special instructions for driver and front passenger

airbag

⇒ “3.4 Special instructions for driver and front passenger air‐

bag”, page 226

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

3. Airbag

233

Содержание Rapid NH 2014
































































































































































































































































































































Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды

Skoda Rapid NH 2014, Руководство по ремонту

Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды