Skoda Rapid NH 2014 страница 127 Скачать руководство пользователя

Страница: 127 / 319

2.16.2

Installing

– The openings -4- under the window run must be masked with

fabric adhesive tape.

Dimensions of adhesive: height = approx. 10 mm, width = approx.

40 mm. 2 pieces.
– Slide the window run -1- into the supports -arrows a-.
– Press the window run -1- evenly all around against the door

flange -2-.

– Press the sealing lip of the door run from the inside against the

door flange.

– Slide in the retaining clip -3- -arrow b-.

Note

♦

The chamfer of the retaining clips must point to the inside of the vehicle.

♦

If the chamfer points to the outside of the vehicle, the -crossed-out red colour-, then the retaining clip must

be turned around.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

2. Door internal parts

119

Содержание Rapid NH 2014
































































































































































































































































































































Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды

Skoda Rapid NH 2014, Руководство по ремонту

Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды