Skoda Rapid NH 2014 Скачать руководство пользователя

Страница: 74 / 319

Note

If it is necessary for the following operations, it is possible to slacken the Bowden cable.

Slacken Bowden cable to bearing bracket
– Twist the Bowden cable -5- by 45° and remove it from the

bracket -arrow a-.

– Turn the Bowden cable - arrow b -until it can be guided out of

the lug in the door lock (Pos. 1) - arrow c -.

Slacken the Bowden cable to the inner door control:
– Twist the Bowden cable -6- by 45° and remove it from the

bracket.

– Turn the Bowden cable -arrow d- until it can be guided out of

the lug in the door lock (Pos.1) -arrow e-.

2.8.2

Installing

Installing
– The installation occurs in reverse order.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

Rep. gr.57 - Front doors, door components, central locking

Содержание Rapid NH 2014
































































































































































































































































































































Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды

Skoda Rapid NH 2014, Руководство по ремонту

Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды