Skoda Rapid NH 2014 Скачать руководство пользователя

Страница: 222 / 319

– Unscrew screw -1- (40 Nm) and loosen the belt end fitting

-2- from the body.

Installing
The installation occurs in reverse order.
– Connect the vehicle battery ⇒ Electrical System; Rep. gr. 27 ;

disconnect and connect the battery .

1.2

Removing and installing the front seat

belt height adjuster

Removing
– Slacken the upper trim panel of the B pillars from the supports

⇒ “3.4 Removing and installing top B-pillar trim panel”,

page 266

– Unscrew the screw -1- (40 Nm) and release the belt deflection

fitting -2- from the seat belt height adjustment.

– Screw out screw -1- (20 Nm) and remove the seat belt height

adjuster -2- from the supports in the support panel.

Installing
– The installation occurs in reverse order.

1.3

Removing and installing the front seat

belt buckle

Removing

Note

On vehicles with automatic seatbelt detection system, the wiring

harness must be separated additionally at the connector station

and it must be released at the seat rack.

– Remove front seat

⇒ “1.1 Removing and installing front seat”, page 286

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

214

Rep. gr.69 - Passenger protection

Содержание Rapid NH 2014
































































































































































































































































































































Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды

Skoda Rapid NH 2014, Руководство по ремонту

Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды