Skoda Rapid NH 2014 Скачать руководство пользователя

Страница: 211 / 319

2.2.2

Removing and installing centre console

1 - Drink holder and storage

area

❑ Clipped onto centre

console.

2 - Screw

❑ Tightening torque - 1.5

Nm.

3 - Cap of handbrake

❑ Clipped onto centre

console.

4 - Centre console
Removing

– Switch off the ignition

and all electrical compo‐

nents.

– Unclip the trim panel for

the shift lever ⇒ Gear‐

box; Rep. gr. 34 .

– Remove armrest (de‐

pending upon vehicle

equipment)

⇒ “2.5 Removing and in‐

stalling the armrest”,

page 206

– Remove cap (Pos. 6).

– Remove screws (Pos.

2).

– Remove=ing handle for

handbrake lever ⇒

braking systems; Rep.

gr. 46 ; Handbrake;

summary of handbrake components .

– Apply handbrake fully.

– Unclip the cap on the handbrake (Pos. 3).

– Press console approx. 30 mm in direction of engine - arrow A - and unclip from the holders for the dash

panel.

– Swivel out console in -direction of arrow B-.

– Disconnect the plug connection of the cigarette lighter (power socket) ⇒ Electrical System - General

notes; Rep. gr. 96 .

– Remove the trim panel from the vehicle.

Installing

– The installation occurs in reverse order.

5 - Storage tray

❑ Clipped onto centre console.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

2. Covers, storage areas and trim panels

203

Содержание Rapid NH 2014
































































































































































































































































































































Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды

Skoda Rapid NH 2014, Руководство по ремонту

Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды