Skoda Rapid NH 2014 страница 163 Скачать руководство пользователя

Страница: 163 / 319

1.13

Prepare body flange for fitting

Carry out the following tasks
– Cut back the sealing compound on the body flange using the

U-shape cutting knife - V.A.G 1561/3- . However do not re‐

move completely.

Note

The remainder of the sealant serves as a base for the newly ap‐

plied glue sealing material. Keep the adhesive surfaces free of

dirt or grease.

WARNING

The activator must not come into contact with paintwork, oth‐

erwise there will be paint damage.

Exception: If the bonding is not carried out immediately after cut‐

ting back, the sealing compound must be activated with the

activator - D 181 801 A1- .
♦ If the body flange was reworked or only partly replaced, clean

this area again after painting and treat it with glass/paint pri‐

mer.

Note

Under some circumstances, it is possible that a laser welding

seam is not present in the area of the adhesive bead. Then the

exposed welding seam must be sealed before gluing the window

with the window pane adhesive.

– If the laser welding seam - 3 - at the metal flange - 4 - is not

covered with an adhesive bead - 1 -, coat the laser welding

seam - 3 - with glass/paint primer - D 009 200 02- - 3 -. After

airing the glass / paint primer, fill the welded seam with window

adhesive - 1 -.

1.14

Installation instructions for all panes

– Apply the adhesive cement all around at a right angle to the

window.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

1. Glued windows

155

Содержание Rapid NH 2014
































































































































































































































































































































Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды

Skoda Rapid NH 2014, Руководство по ремонту

Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды