Skoda Rapid NH 2014 Скачать руководство пользователя

Страница: 48 / 319

Removing
– Remove lock cover - 3 -.
– Disconnect the plug connection from the tailgate lock control

- 1 -.

– Release the nuts -2- (21 Nm) and remove the flap lock -1- from

the tailgate.

Installing
– The installation occurs in reverse order.

2.6

Removing and installing pressurized

gas strut of tailgate

Removing
– Open tailgate, support and lock it into position.
– Use a screwdriver to raise the locking element - 2 - and pull

the pressurized gas strut - 1 - off the ball stud - 3 -.

Note

If the pressurized gas strut is to be re-used, do not remove the

locking device fully from the ball socket, otherwise it will be dam‐

aged.

– 1 - Pressurized gas strut
– 2 - Locking device
– 3 - Ball stud
Installing
– The installation occurs in reverse order.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

Rep. gr.55 - Bonnet, rear lid

Содержание Rapid NH 2014
































































































































































































































































































































Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды

Skoda Rapid NH 2014, Руководство по ремонту

Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды