SIGRIST OilGuard Ex M Скачать руководство пользователя страница 45

Страница: 45 / 60

Instruction Manual OilGuard Ex M

10241E/2

Action

Display (example)

Remarks

3 x

> Adju. <

Retain

Adju.

> Retain <

Adju.

> Adapt <

Adju.

running ...

Wait until the

photometer has
determined the
calibration factors
and the display

changes.

- Measure –

X.XXX FLU

Display of "raw“ check

values without reading
adjustments.

If “Tolerance exceed”

appears in the display,

consult the following
section.

After successful recalibration of the instrument, rebuild to the initial state.

If the nominal and actual values differ from each other too greatly, check the

following points:

Is the serial number of the photometer the same as the one on the control
unit?

Does the nominal value match the one on the control unit?

Is the control unit clean and undamaged?

Are the measuring cell windows clean?

Has the minimum warm-up time of two hours been observed?

If this does not help, please contact customer service (

→

Section 6.4).

What to do if value
is “out of tolerance”

Содержание OilGuard Ex M





























































Результаты поиска

Содержание OilGuard Ex M

Отзывы:

Похожие инструкции для OilGuard Ex M

Бренды по названию

Популярные бренды

SIGRIST OilGuard Ex M, Инструкция по эксплуатации

Результаты поиска

Содержание OilGuard Ex M

Отзывы:

Похожие инструкции для OilGuard Ex M

Бренды по названию

Популярные бренды