Siemens SICAM Q100 7KG95 Series Скачать руководство пользователя страница 343

Страница: 343 / 448

10 Operation at Use of the Display

10.4 Parameterization

343

SICAM Q100, 7KG95xx, Device Manual
E50417-H1040-C522-A6, Edition 06.2019

10.4

Parameterization

Softkeys F1 to F4 are used for parameterization taking the display content into consideration. Proceed as
described in the following menus.

10.4.1

Menu Tree of the Main Menu

Figure 10-6

Menu Tree of the Main Menu

NOTE

Remember that the parameterization on the device is subject to restrictions. Full parameterization requires a
PC and the HTML pages.

1.0

Voltage
Vph-n

2.0

Voltage
Vph-ph

3.0

Current
I

4.0

Active power
P (W)

5.0

React. power
Q1 (var)

6.0

App. power
S (VA)

7.0

Total power
P, Q1, S

8.0

Power factor
PF

9.0

Tot. pwr.factor
PF tot

10.0

Disp. angles

11.0

Frequency
Hz

12.0

THDS voltage
THDS-V

13.0

THDS current
THDS-I

14.0

Phasor diagram

15.0

Harm. voltage
V

16.0

Harm. current
I

17.0

App. energy
VAh

18.0

Active energy
Wh

19.0

React. energy
varh

20.0

Active factor
cos



31.0

Long flicker
ph-n



27.0

28.0

Tariff 7

Tariff 8

30.0

Short flicker
ph-ph



35.0 to 38.0

User def.
Screens 1 to 4

80.0

Settings

PQ events

60.0

50.0

Operation log

32.0

Long flicker
ph-ph

29.0

21.0

Tariff 3

22.0

Tariff 1

23.0

Tariff 2

24.0

Tariff 4



25.0

26.0

Tariff 5

Tariff 6



34.0

Binary in-/
outputs state



Phase unbal.
Vnb, Inb

33.0

Short flicker
ph-n

NOTE

The user-defined screens (35.0 through 38.0) are only visible on the display if they were activated using the
HTML pages (see chapter 9.3.4.2).

MAN_SICAM_Q100_US.book Page 343 Wednesday, June 5, 2019 9:31 AM

Содержание SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Результаты поиска

Содержание SICAM Q100 7KG95 Series

Отзывы:

Siemens SICAM Q100 7KG95 Series, Руководство пользователя, Страница: 343 / 448

Результаты поиска

Содержание SICAM Q100 7KG95 Series

Отзывы: