manualshive.com logo in svg

Siemens SICAM Q100 7KG95 Series, Руководство пользователя, Страница: 124 / 448

Поделиться
Скачать
Siemens SICAM Q100 7KG95 Series Скачать руководство пользователя страница 124

7 Getting Started

7.7 Commissioning

124

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

7.7.3

Starting the Device with the Default IP Address

SICAM Q100 has the following internal default IP address: 

192.168.0.55

.

If you have entered a custom IP address during device configuration, you can temporarily activate the internal 
default IP address of the device if necessary. Proceed as follows:

✧

Hold down the F4 softkey located in the right part of the display side of the device for at least 3 s.

Figure 7-5

Location of the Softkey F4 for Activating the Default IP Address

When you press the softkey F4, SICAM Q100 will reset and use the default IP address until you have set 
a new IP address or switched the device off and on again.

Softkey F4

Default IP Address:  192.168.0.55

Default Subnet Mask: 255.255.255.0

NOTE

Changing the IP address causes the device to reset and the LEDs signal (see chapter 12.3) that the device 
was started with the default IP address.

In this case, the parameterized IP address and the default IP address are displayed on the

Information

 tab,  

Device information

 menu item (see chapter 9.2.7).

MAN_SICAM_Q100_US.book  Page 124  Wednesday, June 5, 2019  9:31 AM

Содержание SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Отзывы:

Нет отзывов