manualshive.com logo in svg

Siemens SICAM Q100 7KG95 Series, Руководство пользователя, Страница: 211 / 448

Поделиться
Скачать
Siemens SICAM Q100 7KG95 Series Скачать руководство пользователя страница 211

9 Operation at Use of a PC

9.3 Configuration of the Device

211

SICAM Q100, 7KG95xx, Device Manual
E50417-H1040-C522-A6, Edition 06.2019

After recording has started, the 

Recording status

 fields shows the entry 

Running

.

✧

If you want to stop the recording, click on 

Stop recording

 and execute the activation.

The 

Recording status

 field shows the entry 

Not running

 and 

Start recording

 is displayed on the user 

interface.

Recording Power Quality Data

When the device is started for the first time, it is necessary for the recording of power quality data that the 

Time 

synchronization

 of the device is set to the current time first. If the time is incorrect, the power quality measure-

ments do not conform to the current time. Proceed as follows:

✧

Refresh the time via 

Ethernet NTP

 or 

Field bus

 in line with chapter 9.3.7.1 or with the device-

internal

 

clock in line with chapter 9.5.3.2.

✧

Configure all necessary parameters (for example, AC measurement, Communication) on the relevant 
tabs, 

except for

 the 

Recording parameters

 settings.

When setting the parameters, make sure that the settings are consistent with each other (for example, 
setting of the flicker lamp model consistent with the primary nominal voltage).

✧

At last

, parameterize the 

Recording parameters

 and activate the settings.

NOTE

The restart of the record is carried out after a power failure automatically.

The status will change from 

Not running

 to 

Running

 when user change and activate parameters.

MAN_SICAM_Q100_US.book  Page 211  Wednesday, June 5, 2019  9:31 AM

Содержание SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Отзывы:

Нет отзывов