Siemens 6DR2210 Скачать руководство пользователя страница 106

Страница: 106 / 270

Manual

1 Technical Description

1.5 Functional description of the structure switches

1.5.6 Controller output structures (S2, S61 to S68)

104

SIPART DR22 6DR2210

C79000-G7476-C154-03

1.5.6.2 S2 = 1:

Three-position step (S) -controller with internal feedback

To control I-acting motorized actuating drives.

In S-controllers with internal feedback the K-controller is followed by an internal position

controller. The positioning control circuit consists of a comparator with following three-position

switch with hysteresis and an integrator in the feedback. The I-function of the actuator is

simulated by the integrator with adjustable floating time tY (parameterization mode onPA) which

replaces the position feedback. To ensure the internal integrator and the K-controller output do

not drift apart or into saturation in time, both are set back rhythmically by the same amount

(synchronized). The y-output is only a relative manipulated variable (y’). It is therefore not

possible to perform a manipulated variable limiting of ya and an absolute value preset of y

and

ys. The safety manipulated variable ys is preset as a direction-dependent continuous contact.

At YS

50 % (oFPA), --

y switches, at YS

≥

50 %, +

y switches to continuous contact so that

the end positions represent the safety position. The position controller has an adjustable

minimum pulse length (tE) and pause (tA) with which the response threshold of the position

controller is set indirectly:

-- Switching on

= 2

100 %

⋅

-- Switching off

100 %

⋅

-- Hysteresis

-- A

100 %

⋅

-- Pause

100 %

⋅

-- tY set floating time (parameterization mode onPA)

After a pulse pause A

must be set up at least as a deviation until an actuating pulse with

length tE is output. A

can remain as a constant control error of the position control circuit.

can be set up after an actuating pulse as a deviation until an actuating pulse is output in the

same or opposite direction. When time tA has expired, the position controller reacts accordingly

to the set tE.

Setting criteria of tA and tE, see chapter 4.3, page 218.

The position feedback y

via FE6 is only used to display the manipulated variable in S-control-

lers with internal feedback. If it is not connected, S67 is set to 0, the y-display (14) is then dark.

Содержание 6DR2210















































































































































































































































































Результаты поиска

Содержание 6DR2210

Отзывы:

Похожие инструкции для 6DR2210

Бренды по названию

Популярные бренды

Siemens 6DR2210, Руководство пользователя

Результаты поиска

Содержание 6DR2210

Отзывы:

Похожие инструкции для 6DR2210

Бренды по названию

Популярные бренды