background image

-48-

SE

RV

IC

E

Model W1807 7 

1

2

 HP Heavy-Duty Industrial Tilting Spindle Shaper

Troubleshooting

This section covers the most common problems and corrections with this type of 

machine. 

WARNING! DO NOT make any adjustments until power is disconnected and 

moving parts have come to a complete stop!

PROBLEM

POSSIBLE CAUSE

CORRECTIVE ACTION

Motor does not start or a 
breaker trips.

1.  Fuse has blown.
2.  Emergency stop button is engaged; 

is faulty.

3.  Motor connection wired 

incorrectly.

4.  Thermal overload relay has 

tripped.

5.  Contactor not getting energized; 

has burnt contacts.

6.  Wall fuse/circuit breaker is blown/

tripped.

7.  Power supply is at fault or 

switched off.

8.  Forward/reverse switch at fault.
9.  Wiring is open; has high 

resistance.

10. Motor is at fault.

1.  Correct short; replace fuse in electrical box.
2.  Rotate emergency stop button until it pops out; 

replace it if faulty.

3.  Correct motor wiring connections; refer to diagram 

inside motor junction wiring box cover.

4.  Turn amperage dial to increase working amps and 

push the reset pin; replace if tripped multiple 
times.

5.  Test for power on all legs and contactor operation; 

replace unit if faulty.

6.  Ensure circuit is correct size for machine load 

(refer to 

Page 10

); replace weak breaker.

7.  Ensure hot lines have correct voltage on all legs 

and main power supply is switched on.

8.  Replace faulty forward/reverse switch.
9.  Check for broken wires or disconnect/corroded 

connections, and repair/replace as necessary.

10. Test/repair/replace motor.

Machine stalls or is 
underpowered.

1.  Wrong workpiece material.

2.  Feed rate too fast for task.
3.  Dust collection is poor.

4.  V-belt slipping.
5.  Motor connection is wired 

incorrectly.

6.  Pulley slipping on shaft.
7.  Motor bearings are at fault.

8.  Machine is undersized for task.

9.  Motor has overheated.
10. Contactor not getting energized or 

has poor contacts.

11. Motor is at fault.

1.  Use wood with correct moisture content (less than 

20%), without glues, and has little pitch/resins.

2.  Decrease feed rate.
3.  Seal all leaks, size ducts correctly, eliminate bends, 

and refer to Dust Collection Basics Handbook (ISBN 
0-9635821-2-7) for further recommendations.

4.  Re-tention/replace V-belt (refer to 

Page 41

).

5.  Correct motor wiring connections.

6.  Replace loose pulley/shaft.
7.  Test by rotating motor shaft; rotational grinding/

loose shaft requires bearing replacement.

8.  Use sharp cutters; reduce the feed rate/depth of 

cut.

9.  Clean off motor, let cool, and reduce workload.
10. Test for power on all legs and contactor operation; 

replace if faulty.

11. Test/repair/replace motor.

Machine has vibration or 
noisy operation.

1.  Motor or component is loose.

2.  V-belt worn or loose.
3.  Motor fan is rubbing on fan cover.
4.  Cutter or spindle is at fault.

5.  Machine not stable on floor.
6.  Elevation housing is loose.
7.  Pulley is loose.

1.  Inspect/replace stripped or damaged fasteners, and 

retighten with thread locking fluid.

2.  Inspect/replace V-belt (refer to 

Page 41

).

3.  Replace dented fan cover/fan.
4.  Replace cutter; tighten/replace loose spindle (

Page 

44

).

5.  Secure machine to floor; reposition; re-shim.
6.  Replace cracked elevation housing.
7.  Realign/replace pulley shaft, pulley, set screw, and 

key as required.

Troubleshooting

Motor & Electrical

Содержание W1807

































































Отзывы: