Sharp AR-BC260 Скачать руководство пользователя страница 230

Страница: 230 / 308

AR-BC260 TROUBLESHOOTING 11 - 3

6. Details

Mirror return trouble

Paper feed motor lock trouble

Transfer belt lift motor trouble

Transfer belt motor trouble

Shift motor trouble

Full wave signal not provided

Full wave signal width abnormality

Main power switch abnormality detection

RIC copy inhibit signal reception

ICU-OPE communication trouble (ICU/OPE
detection)

FAX battery abnormality

RTC read trouble

EEPROM read/write error (ICU detection)

EEPROM check sum error (ICU detection)

FAX backup SRAM memory check sum error

Production No. data discrepancy (ICU

⇔

ICU)

EEPROM read/write error (SCN)

Adjustment value check sum error (SCN)

EEPROM read/write error (PCU)

Adjustment value check sum error (PCU)

ADU alignment plate operation abnormality

Desk communication trouble

Desk tray 1 lift motor trouble

Desk tray 2 lift motor trouble

Desk tray 3 lift motor trouble

LCC lift motor trouble

Desk transport motor trouble

LCC communication trouble

LCC transport motor trouble

LCC 24V power abnormality

Desk incompatibility trouble

LCC incompatibility trouble

RIC communication trouble

CPT-ASIC trouble (MFP PWB trouble)

Main
code

Sub

code

Title

PCU PWB error

Display

Lamp/Message

Phenomenon Detail

When the power is turned
on, conformity of the PCU
PWB and the PCU ROM is
checked to be found that
there is no conformity.

Section

PCU PWB

Case 1

Cause

PCU PWB trouble

Check &
Remedy

Replace the PCU PWB.

Case 2

Cause

PCU PWB mistaken

Check &
Remedy

Replace the PCU PWB.

Main
code

Sub

code

Content

Main
code

Sub

code

Title

Transfer charger trouble (Black)

Display

Lamp/Message

Phenomenon Detail

The difference between the
belt surface output and the
K-color patch density output
does not reach the specified
level. (Judged when
installing a new developing
unit.)

Section

Transfer

Case 1

Cause

TC-K output abnormality

Check &
Remedy

TC-K analog input/output
abnormality.
Replace the TC PWB.

Case 2

Cause

MC output abnormality

Check &
Remedy

Replace the MC PWB.

Case 3

Cause

Transfer unit trouble

Check &
Remedy

Replace the transfer unit.

Case 4

Cause

PCU PWB trouble

Check &
Remedy

Replace the PCU PWB.

Case 5

Cause

Connector, harness trouble
(PCU PWB, TC PWB, MC
PWB, transfer unit)

Check &
Remedy

Check contact. Replace the
harness. Replace the PWB.

Main
code

Sub

code

Title

Image data memory trouble

Display

Lamp/Message

Phenomenon Detail

The ICU image data
memory (SDRAM) cannot
be detected as 256MB or
more. The required SDRAM
capacity for the model is not
provided.

Section

ICU PWB

Case 1

Cause

The SDRAM of ICU PWB is
not installed. The SDRAM
of ICU PWB is improperly
installed.

Check &
Remedy

Check installation of the
SDRAM of ICU ASIC PWB.

Case 2

Cause

The SDRAM of ICU PWB
does not operate properly.

Check &
Remedy

Use SIM 22-10 to check the
capacity of the SDRAM.
Replace the SDRAM of ICU
PWB.

Case 3

Cause

ICU PWB abnormality

Check &
Remedy

Replace the ICU PWB.

Содержание AR-BC260





















































































































































































































































































































Результаты поиска

Содержание AR-BC260

Отзывы:

Бренды по названию

Популярные бренды

Sharp AR-BC260, Руководство по обслуживанию

Результаты поиска

Содержание AR-BC260

Отзывы:

Бренды по названию

Популярные бренды