Sharp AR-BC260 Скачать руководство пользователя страница 188 | Manualshive

Страница: 188 / 308

background image

AR-BC260 SIMULATION 9 - 50

(Items to be set)

(Items to be set)

2. Select the adjustment point with the scroll key.
3. Enter the adjustment value of the selected point with the 10-

key and press the [OK] key. (The entered value is set.)

When the [EXECUTE] key is pressed, the color balance
adjustment check pattern corresponding to the entered adjustment
value is printed.

46

-16

Purpose

Adjustment

Function
(Purpose)

Used to adjust the gamma and density.
(Monochrome mode) (The adjustment check pattern
is printed.)

Section

Image process (ICU)

Item

Picture quality

Density

Operation/
Procedure

1. Select the adjustment point with the scroll key.
2. Enter the adjustment value of the selected point

with the 10-key and press the [OK] key. (The
entered value is set.)

When the [EXECUTE] key is pressed, the color
balance adjustment check pattern corresponding to
the entered adjustment value is printed.

Display

Min.

Value

Max.

Value

Default

A

POINT1

373

627

500

↓

↓

↓

↓

↓

O

POINT15

373

627

500

46

-19

Purpose

Adjustment

Function
(Purpose)

1. Used to set half tone (gamma) selection

(destination setting) in the monochrome auto
copy mode.

2. Used to set the automatic exposure operation

mode (Monochrome copy mode, FAX mode,
monochrome scanner mode).

Section

Scanner (reading)

Item

Picture quality

Operation/
Procedure

1. Select the adjustment mode with the scroll keys.
2. Set the half tone density (gamma) with [MODE 1]

/ [MODE 2] keys.

3. Select the adjustment mode with the scroll keys.
4. Select the operation mode of the automatic

exposure mode with [ON]/[OFF] keys.

Display Set mode

Content

Destination

Default

AE
MODE

MODE 1
(AUTO 1)

The half-tone
density is higher
than that of AUTO 2
mode.

Japan

MODE 2

(AUTO 2)

MODE 2
(AUTO 2)

The half-tone
density is lower than
that of AUTO 1
mode.

Except
Japan

Display

Setting

mode

Content

Default

AE
STOP
MODE

OFF

The automatic density (exposure)
control is performed on real time.
(The density level is changed
according to the document
pattern on real time.)

AE STOP
COPY: OFF
AE STOP
FAX: OFF

ON

The density at the lead edge of
the document is scanned, and the
overall density (exposure) level is
determined by the scanned
density level. (The overall density
level is fixed.)

AE STOP
SCAN: ON

46

-20

Purpose

Adjustment

Function
(Purpose)

Used to adjust copy color balance (All color copy
mode gamma/density adjustment) (All color copy
mode color balance/gamma/density are changed.)
Same as SIM 46-21, however, printing is not
performed.

Section

Image process (ICU)

Item

Picture quality

Color balance

Operation/
Procedure

1. Select the color to be adjusted with the color key

(K/C/M/Y).

2. Select the adjustment point with the scroll key.
3. Enter the adjustment value of the selected point

with the 10-key and press the [OK] key. (The
entered value is set.)

Display

Min.

Value

Max.

Value

Default

A

POINT1

245

755

500

↓

↓

↓

↓

↓

O

POINT15

245

755

500

46

-21

Purpose

Adjustment

Function
(Purpose)

Used to adjust copy color balance (All color copy
mode gamma/density adjustment) (All color copy
mode color balance/gamma/density are changed.)

Section

Image process (ICU)

Item

Picture quality

Color balance

Operation/
Procedure

1. Select the color to be adjusted with the color key

(K/C/M/Y).

«
...
186
187
188
189
190
...
»

Содержание AR-BC260





















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AR-BC260

Бренд: QMS Страницы: 122

Бренд: QMS Страницы: 306

Color imageCLASS MF8580Cdw

Бренд: Canon Страницы: 36

Color imageCLASS MF8580Cdw

Бренд: Canon Страницы: 20

Color imageCLASS MF8280Cw

Бренд: Canon Страницы: 24

Color imageCLASS MF8080Cw

Бренд: Canon Страницы: 39

Color imageCLASS MF8050Cn

Бренд: Canon Страницы: 32

Color imageCLASS LBP7660Cdn

Бренд: Canon Страницы: 2

Color imageCLASS 8180c

Бренд: Canon Страницы: 24

Бренд: Canon Страницы: 30

C3000 - MultiPASS Color Inkjet Printer

Бренд: Canon Страницы: 41

Color imageCLASS MF8170c

Бренд: Canon Страницы: 2

Color imageCLASS MF8170c

Бренд: Canon Страницы: 98

Color imageCLASS MF8170c

Бренд: Canon Страницы: 8

Color imageCLASS MF8080Cw

Бренд: Canon Страницы: 46

Color imageRUNNER LBP5360

Бренд: Canon Страницы: 3

Бренд: Xerox Страницы: 532

Бренд: Xerox Страницы: 174

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды