Sharp AR-BC260 Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 308

background image

AR-BC260 SETTING AND ADJUSTMENTS 8 - 32

4) Cancel the simulation mode, and make a copy in the normal

mode to check the copy density in the white area and the low-
density area by using the test chart (UKOG-0283FCZZ).

In this simulation mode, press CLOSE key to jump to the normal
copy mode and make actual copies of the service chart and user
documents. In this manner, the adjustment result can be checked.

The adjustment can be performed also by switching between the
simulation mode and the normal copy mode alternately and check-
ing the adjustment result with actual copies.

This adjustment must be performed in the following cases:

∗

When a U2 trouble occurs.

∗

When the MFP PWB is replaced.

∗

When the EEPROM of the MFP PWB is replaced.

Used to adjust the gamma and the density in each copy mode individually. The adjustment in each copy mode is not required normally, but
is performed when the user requests it.

1) Enter either of SIM 46-10 to 46-16 modes.

(Select the simulation according to the copy mode to be
adjusted.)

Serviceman chart (Color patch section)

Check the copy density in the low-density area
and the white area of the color patch section.

ADJ 11E

Copy color balance density adjustment (each copy mode) (Normally unnecessary to adjust.)

Copy mode

Adjustment (Simulation)

Color balance/

density

adjustment of

each copy mode

Collective color

balance/density

adjustment of all

copy modes

Low-density

area color

balance/density

adjustment

Main

Sub

Main

Sub

Main

Sub

Full color

AUTO

Auto

Text/printed
photo

46

12

46

21/20/

24

46

1

TEXT

NORMAL

Text

Normal

11

COLOR TONE ENHANCEMENT

Color emphasis

COPT TO COPY

Copy document

10

MAP

NORMAL

Map

Normal

11

COLOR TONE ENHANCEMENT

Color emphasis

PRINTED
PHOTO

NORMAL

Printed photo

Normal

12

COLOR TONE ENHANCEMENT

Color emphasis

COPT TO COPY

Copy document

10

TEXT/PRINTED
PHOTO

NORMAL

Text/printed
photo

Normal

12

COLOR TONE ENHANCEMENT

Color emphasis

COPT TO COPY

Copy document

10

PHOTOGRAPH NORMAL

Photograph

Normal

13

COLOR TONE ENHANCEMENT

Color emphasis

TEXT/PHOTO

NORMAL

Text/Photograph Normal

14

COLOR TONE ENHANCEMENT

Color emphasis

Single color
(Affected by
the adjustment
result of full
color mode)

TEXT

NORMAL

Text

Normal

25/(26)

COPT TO COPY

Copy document

MAP

NORMAL

Map

Normal

PRINTED
PHOTO

NORMAL

Printed photo

Normal

COPT TO COPY

Copy document

TEXT/PRINTED
PHOTO

NORMAL

Text/printed
photo

Normal

COPT TO COPY

Copy document

PHOTOGRAPH NORMAL

Photograph

Normal

TEXT/PHOTO

NORMAL

Text/Photograph Normal

«
...
123
124
125
126
127
...
»

Содержание AR-BC260





















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AR-BC260

Бренд: Oki Страницы: 48

Бренд: Oki Страницы: 42

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 8

Бренд: Oki Страницы: 13

Бренд: Oce Страницы: 2

Бренд: Oki Страницы: 193

Бренд: Partner Страницы: 9

Бренд: VASTEX Страницы: 2

WorkCentre 4265

Бренд: Xerox Страницы: 20

Бренд: Xerox Страницы: 11

Бренд: TallyGenicom Страницы: 2

Бренд: OmniPrint Страницы: 44

Бренд: Posnet Страницы: 2

WorkCentre 7830

Бренд: Xerox Страницы: 12

5550N - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 16

Бренд: DPM Страницы: 2

Бренд: HandTop Страницы: 97

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды