manualshive.com logo in svg

Sharp AR-BC260, Руководство по обслуживанию

Поделиться
Скачать
Sharp AR-BC260 Скачать руководство пользователя страница 146

AR-BC260  SIMULATION  9 - 8

46

5

Used to adjust the image density 
(monochrome mode) in the network 
scan mode. 

Adjustment

Scanner (reading)

Picture quality

Density

6

1) Used to set the CCD black level 

offset level.

2) Used to set the CCD white level 

gain.

Adjustment

Scanner (reading)

Picture quality

8

Image color balance adjustment in 
the network scan mode

Adjustment

Scanner (reading)

Picture quality

9

Used to set the exposure adjustment 
value in each document feeder unit 
mode.

Setting

Automatic document 
feeder

Picture quality

10

Used to adjust the copy color 
balance (color) (copy document 
mode) (gamma/density adjustment 
for each color)

Adjustment

Image process (ICU)

Picture quality

Color balance

11

Used to adjust the copy color 
balance (color) (text mode/map 
mode) (gamma/density adjustment 
for each color)

Adjustment

Image process (ICU) 

Picture quality

Color balance

12

Used to adjust the copy color 
balance (color) (text/printed photo 
mode/Photograph mode) (gamma/
density adjustment for each color)

Adjustment

Image process (ICU) 

Picture quality

Color balance

13

Used to adjust the copy color 
balance (color) (photograph mode) 
(gamma/density adjustment for each 
color)

Adjustment

Image process (ICU) 

Picture quality

Color balance

14

Used to adjust the copy color 
balance (color) (text/photograph 
mode) (gamma/density adjustment 
for each color)

Adjustment

Image process (ICU) 

Picture quality

Color balance

15

Engine color balance manual 
correction

Adjustment

Image process (ICU) 

Picture quality

Density

16

Used to adjust the gamma and 
density. (Monochrome mode) (The 
adjustment check pattern is printed.)

Adjustment

Image process (ICU) 

Picture quality

Density

19

1. Used to set half tone (gamma) 

selection (destination setting) in 
the monochrome auto copy 
mode.

2. Used to set the automatic 

exposure operation mode 
(Monochrome copy mode, FAX 
mode, monochrome scanner 
mode).

Adjustment

Scanner (reading)

Picture quality

20

Used to adjust copy color balance 
(All color copy mode gamma/density 
adjustment) (All color copy mode 
color balance/gamma/density are 
changed.) Same as SIM 46-21, 
however, printing is not performed.

Adjustment

Image process (ICU)

Picture quality

Color balance

21

Used to adjust copy color balance 
(All color copy mode gamma/density 
adjustment) (All color copy mode 
color balance/gamma/density are 
changed.)

Adjustment

Image process (ICU)

Picture quality

Color balance

23

Used to set Enable/Disable of half-
tone high-density correction.

Setting

Picture quality

Color balance

24

Used to adjust the copy color 
balance automatically. (All color copy 
mode gamma/density adjustment)

Adjustment

Picture quality

Color balance

25

Used to adjust copy color balance 
(Single color mode)

Adjustment

Image process (ICU)

Picture quality

Color balance

26

Used to set the copy color balance 
adjustment to the default. (Single 
color copy mode)

Adjustment

Image process (ICU)

Picture quality

Color balance

27

Used to adjust the gamma/density in 
the black edge section of the copy 
mode image. (Black text and black 
line reproduction adjustment)

Adjustment

Image process (ICU)

Picture quality

Color balance

28

Used to check pre-scanning 
operation for automatic recognition of 
document in the color auto copy 
mode. (This simulation is used only 
in production, and not used in the 
market.)

Adjustment

Image process (ICU) 

Picture quality

Color balance

Code

Function (Purpose)

Purpose

Section

Item

Main

Sub

Содержание AR-BC260





















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды