Sharp AR-BC260 Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 308

background image

AR-BC260 SETTING AND ADJUSTMENTS 8 - 21

(1) Note for the copy color balance/density adjustment

(Necessary conditions for execution of the copy color balance/density adjustment)

Before execution of the copy color balance/density adjustment, check that all the adjustments related to the copy color balance and density
have been completed properly.

The importance level is as shown below.

(Adjustment items which directly affect the copy color balance and density and must be checked or adjusted
before execution of the image quality adjustment)

1) Adjustment items: ADJ 2, ADJ 3, ADJ 4

The user color balance adjustment must be set to the center (default).

The set value of SIM 46-27 is set to the default.

The set value of the following simulation must be set to the default.

Adjustment item

Adjustment

value

Note

IMAGE
LOSS

Lead edge image
loss

4.0 ± 1.0mm

The greater the set value is,
the greater the image loss is.

DEN-A

Lead edge void
area

4.0 ± 1.0mm

The greater the set value is,
the greater the void area is.

DEN-B

Rear edge void
area

4.0 ± 1.0mm

The greater the set value is,
the greater the void area is.

ADJ 11

Copy color balance/density adjustment

JOB No

ADJUSTMENT ITEM LIST

SIMULATION

ADJ 2

Image density sensor adjustment

44-2/44-13

ADJ 3

Image focus, image skew adjustment (LED (writing) unit)

64-1/61-4

ADJ 4

Image registration adjustment

ADJ 4A Image registration adjustment (Auto adjustment)

50-22

ADJ 4B Image registration adjustment (Manual adjustment)

50-20

Item

Purpose

Note

User color balance setting: Default (Center) (Special function) Set the color balance to the standard state. Check that it is set to the center.

SIM

No

Display/Item

Setting

(Default)

Content

Phenomenon when the set

value is changed

Phenomenon occurring

when the adjustment

value is not within the

normal value range.

Note

46-27

A

BLACK TEXT
(SLOPE)

50

Black image edge section
gamma (tilt) adjustment
(Black text and black line
reproduction adjustment)

When the set value is
increased, the contrast of
black line and black text
outline sections is reduced.
On the contrary, when the set
value is decreased, the
contrast is increased.
(Sharpness of black text and
black lines is changed.) (Text/
Printed photo, Text, Text/
Photograph copy mode)

The contrast and
density of lines and text
outline section are
changed. (Sharpness
of text and lines is
changed.) (Text/Printed
photo, Text, Text/
Photograph copy
mode)

For image
quality
adjustment,
set to 50.

B

BLACK TEXT
(INTERCEPT)

50

Black image edge section
density (overall level)
adjustment (Black txt and
black line reproduction
adjustment)

The density of black lines and
black text outline is changed.
(Text/Printed photo, Text,
Text/Photograph copy mode)

SIMNo

Item

Setting

(Default)

Phenomenon when the set value is

changed

Note

46-1

A – R

50

The density and color balance in the low
density section of color copy are changed.

Set to the default when adjusting the copy quality.
Do not adjust the density in the low density section by
using this simulation.

46-2

A – K

50

The density in the low density section of
monochrome copy is changed.

46-10 to 16

A – O

500

The color copy density and color balance
are changed. (each copy mode)

Set to the default when adjusting the copy quality.

46-20

A – O

500

The color copy density and color balance
of all copy modes are changed.

Set to the default when adjusting the copy quality.

«
...
112
113
114
115
116
...
»

Содержание AR-BC260





















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AR-BC260

Бренд: TDT Страницы: 15

Бренд: Unitech Страницы: 2

Бренд: BadgePass Страницы: 2

Бренд: VASTEX Страницы: 15

Бренд: Xerox Страницы: 130

Бренд: Xerox Страницы: 793

Бренд: Olivetti Страницы: 139

Бренд: Oki Страницы: 20

BIZHUB 8050 CF5001

Бренд: Konica Minolta Страницы: 20

invitrogen EVOS FL

Бренд: Thermo Scientific Страницы: 6

Бренд: OKIDATA Страницы: 39

Бренд: Bang & Olufsen Страницы: 4

EMBEDDED UNIT EU

Бренд: Epson Страницы: 28

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 2

Бренд: Epson Страницы: 2

Бренд: Epson Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды