Sharp AR-BC260 Скачать руководство пользователя страница 200 | Manualshive

Страница: 200 / 308

background image

AR-BC260 SIMULATION 9 - 62

3. Press the [EXECUTE] key.

∗

If there is no paper on the duplex tray, one sheet of the
selected paper is fed and transported to the duplex tray.
Then the entered value in procedure 3 is set and the
alignment plate moves according to the home position
corresponding to the entered value.

∗

The paper sizes which can be used for transport and
alignment plate adjustment with SIM52-01 are LT, LTR, A4,
A4R, B5, B5R, 16K, and 16KR only. (For the other sizes,
"FEED ENABLE" occurs.)

(Set items)

• When the set value is changed by 1, it is changed by about

0.2mm. When the set value is increased, the alignment plate
paper width is narrowed. The adjustment value can be adjusted
in the increment of ±50 with 50 as the center value.

(Set value (for manual adjustment))

(Manual adjustment display)

(Items to be set)

Item

Set range

Default

A

Intermediate tray alignment plate
adjustment value (Manual feed)

0 – 99

50

B

Intermediate tray alignment plate
adjustment value (Cassette 1)

0 – 99

50

C

Intermediate tray alignment plate
adjustment value (Cassette 3)

0 – 99

50

D

Intermediate tray alignment plate
adjustment value (Cassette 4)

0 – 99

50

E

Intermediate tray alignment plate
adjustment value (LCC)

0 – 99

50

53

53

-08

Purpose

Adjustment

Function
(Purpose)

Used to adjust the document feeder unit document
scanning position.

Section

Automatic document feeder

Item

Operation

Operation/
Procedure

The automatic or manual adjustment of the
document mirror scanning position of the document
feeder unit is performed.
Press [AUTO] key for the automatic adjustment, and
press [MANUAL] for the manual adjustment.

[Automatic adjustment]
1. The adjustment value stored in the EEPROM is

displayed in "AUTO ADJUST VALUE."

2. When [EXECUTE] key is pressed, the

adjustment value is automatically obtained and
displayed and saved in the EEPROM at the
same time.

[Manual adjustment]
1. Enter the set value with the 10-key and press the

[OK] key to store the set value.

Item

Description

Set range Default

A MANUAL

ADJUST VALUE

Document feeder unit
scanning position
adjustment (for
manual adjustment)

1 – 99

50

60

60

-01

Purpose

Operation test/check

Function
(Purpose)

Used to check the operation of ICU PWB image
DRAM read/write.

Section

ICU (Memory)

Item

Operation

Operation/
Procedure

Press the [EXECUTE] key, and memory read/write
operation check is started.
After completion of check, the result is displayed
with NG or OK.

61

61

-04

Purpose

Adjustment

Function
(Purpose)

Used to adjust the scanner (writing) unit (LED array
unit) skew.

Section

Scanner (writing)

Item

Operation

Operation/
Procedure

1. Set the print conditions of the scanner (writing)

unit (LED array unit) skew adjustment pattern.

2. Press the [EXECUTE] key.
The scanner (writing) unit (LED array unit) skew
adjustment pattern is printed.

Display

Content

Min.

Value

Max.

Value

Default

A PATTERN

Print pattern specification
1: SKEW--- Used to

check scan tilt.

2: FOCUS --- Used to

check/adjust focus.

1

2

1

B LINE PITCH Dot print width (N-1)

specification

1

10

7

C POSITION

Pattern output area
selection

1

12

6

«
...
198
199
200
201
202
...
»

Содержание AR-BC260





















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AR-BC260

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 52

Бренд: Oki Страницы: 117

Бренд: Oki Страницы: 45

Бренд: Oki Страницы: 112

Бренд: Oki Страницы: 115

Бренд: Oki Страницы: 2

EasyCoder 501 SA

Бренд: UBI Страницы: 214

Бренд: UBI Страницы: 64

Бренд: Oki Страницы: 98

Бренд: A&D Страницы: 31

Бренд: Oki Страницы: 132

VERSAJET MP3200 Series

Бренд: Cino Страницы: 18

Бренд: Konica Minolta Страницы: 108

Бренд: Konica Minolta Страницы: 7

Бренд: Toshiba Страницы: 242

Бренд: Toshiba Страницы: 72

Бренд: Toshiba Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды