Sharp AR-BC260 Скачать руководство пользователя страница 198

Страница: 198 / 308

AR-BC260 SIMULATION 9 - 60

14: Main scanning direction rough adjustment 1 Yellow patch print

error

15: Sub scanning direction rough adjustment 1 Cyan patch print

error

16: Sub scanning direction rough adjustment 1 Magenta patch

print error

17: Sub scanning direction rough adjustment 1 Yellow patch print

error

18: Main scanning direction rough adjustment 2 Cyan patch print

error

19: Main scanning direction rough adjustment 2 Magenta patch

print error

20: Main scanning direction rough adjustment 2 Yellow patch print

error

21: Sub scanning direction rough adjustment 2 Cyan patch print

error

22: Sub scanning direction rough adjustment 2 Magenta patch

print error

23: Sub scanning direction rough adjustment 2 Yellow patch print

error

98: Regist sensor error

99: Other error

When the adjustment value is changed, the image losses at the
four corners are changed uniformly.

2. The self print chart is printed, and the machine is brought into

the self print chart scan standby mode.

3. Select [SCAN], and the outputted self print chart is scanned.
4. Select [FINISH] to display the result display menu.

[DATA]: The scanned data are displayed.

• When the set value is 50 at transfer ON timing, the transfer

operation is turned on immediately when the paper lead edge
passes beneath the drum.

• When the set value is 50 at transfer OFF timing, the transfer

operation is turned off immediately when the paper rear edge
passes beneath the drum.

• When the transfer ON/OFF timing value is decreased, the

transfer ON/OFF timing is advanced for the paper.

• When the transfer ON/OFF timing value is increased, the

transfer ON/OFF timing is delayed for the paper.

• Change of ±1 corresponds to about 10ms. The set range is –

490 to +490ms

-27

Purpose

Adjustment

Function
(Purpose)

Used to adjust image loss in the FAX/scanner mode.

Section

FAX/Scanner

Item

Picture quality

Image position

Operation/
Procedure

1. Select the adjustment mode with the scroll key.
2. Enter the adjustment value at the selected point,

and press the [OK] key. The entered value is set.

Display

Content

Min.

Value

Max.

Value

Default

FAX MODE image loss

PUSH SCAN MODE image loss

PULL SCAN MODE image loss

-28

Purpose

Adjustment

Function
(Purpose)

Used to adjust automatic void (service installation
adjustment).

Item

Picture quality

Image position

Operation/
Procedure

1. [ALL OPTION CS]: Select "For service

installation adjustment."
[CS ADJ]: Individual adjustment of cassette
[OC ADJ]: OC adjustment
[SPF ADJ]: SPF adjustment

[PRINT]: When [AUTO] is selected, the self print for

adjustment of CS1 and that for adjustment of MFT
are printed. (When [SPF] is selected, the output is
made from the currently set cassette.)

-01

Purpose

Adjustment

Function
(Purpose)

Used to adjust the transfer voltage ON timing.

Section

Process (Photoconductor, developing,
transfer, cleaning)

Transfer

Item

Operation

Operation/
Procedure

1. Select the adjustment mode with the scroll key.
2. Enter the set value with the 10-key and press the

[OK] key to set the entered value.

Item

Description on item

Set

range

Default

A NORMAL ON

TIMING

Used to set the transfer
ON timing for the paper
lead edge except for OHP.

1 – 99

B NORMAL OFF

TIMING

Used to set the transfer
OFF timing for the paper
rear edge except for OHP.

1 – 99

C OHP ON

TIMING

Used to set the transfer
ON timing for the lead
edge of OHP.

1 – 99

D OHP OFF

TIMING

Used to set the transfer
OFF timing for the rear
edge of OHP.

1 – 99

Содержание AR-BC260





















































































































































































































































































































Результаты поиска

Содержание AR-BC260

Отзывы:

Бренды по названию

Популярные бренды

Sharp AR-BC260, Руководство по обслуживанию

Результаты поиска

Содержание AR-BC260

Отзывы:

Бренды по названию

Популярные бренды