SEW-Eurodrive MAXOLUTION MAXO-RPS-.-R Series Скачать руководство пользователя страница 37

Страница: 37 / 60

Startup

Software startup

Assembly and Operating Instructions – Parallel Arm Kinematics Kit

9. Ensure that the angle of the rotation axis is 0° (±0.1°) and that of the inclination

axis is -90° (±0.1°). Check the value in MOVISUITE

10. Remove the referencing tool.

5.5

Software startup

5.5.1

Requirements

•

Check the installation of the controller, the inverter and the connection of the en-
coders.

•

Observe the installation notes in the documentation of the respective device and
software components.

•

The devices to be put into operation are displayed in the MOVISUITE

project and/

or network view (controller and inverter).

•

The latest firmware is installed on the MOVI-C

CONTROLLER. The controller is

supplied with voltage and started. The controller is connected to the engineering
PC and can be scanned in MOVISUITE

5.5.2

Sequence

Startup procedure:

1. Create MOVISUITE

project.

2. Add axes.

3. Configure the axes.

4. Add MultiMotion.

5. Configure MultiMotion.

6. Create new IEC editor project.

7. Integrate MOVIKIT

Robotics.

8. Replace the configuration.

9. Adjust the configuration.

10. Connect the axes to the robot.

11. Start the control program.

12. Start the robot monitor.

13. Start up the simulated robot.

14. Start up the real robot.

15. Program the robot.

16. Realize the control via the process controller.

5.5.3

Creating the MOVISUITE

project

Proceed as described in the MOVISUITE

documentation.

5.5.4

Adding and configuring axes

1. Add a structure node for the robot. Click "Adding structure node" in the context

menu of the controller. Enter a name for the structure node.

25797530/EN – 04/2018

Содержание MAXOLUTION MAXO-RPS-.-R Series





























































Результаты поиска

Содержание MAXOLUTION MAXO-RPS-.-R Series

Отзывы:

Похожие инструкции для MAXOLUTION MAXO-RPS-.-R Series

Бренды по названию

Популярные бренды

SEW-Eurodrive MAXOLUTION MAXO-RPS-.-R Series, Руководство по сборке и эксплуатации

Результаты поиска

Содержание MAXOLUTION MAXO-RPS-.-R Series

Отзывы:

Похожие инструкции для MAXOLUTION MAXO-RPS-.-R Series

Бренды по названию

Популярные бренды