Sea Tel ST14 Скачать руководство пользователя страница 9

Страница: 9 / 84

ST14 Ku-Band TVRO

Installation

1-3

1.3.

Required Tools

The following tools will be required to install the ST14:

Masking tape

Center punch

Hammer

Electric Drill

7mm Drill Bit

1” hole saw

Small hand or electric saber saw

10mm Socket Wrench or Nut Driver

10mm Open-end Wrench

10.

1/8” straight blade screwdriver

11.

T-20 Torx screwdriver

1.4.

Prepare the Antenna Radome mounting location

Lay the Installation Template (drawing 126355) on the mounting surface location that you have chosen to
mount the radome on.

Align the radome “bow” mark on the template to be parallel to the bow of the boat. By default the

orientation of the “Sea Tel” logo is oriented towards BOW. Adjust the position of the “Bow” marker on

template to orient the LOGO where you want it. When you are satisfied with the position, tape the template

in place.

Using the center punch and hammer, mark the locations of the four radome mounting holes and the cable
passage. Remove the template drawing.

Drill the four radome mounting holes using a 7mm drill bit and the cable passage hole using the 1” hole saw.

1.5.

Prepare the Antenna Control Panel mounting location

Lay the Installation Template (drawing 126355) on the mounting surface location that you have chosen to

mount the Antenna Control Panel in.

Adjust the position of the template to center the Antenna Control Panel cutout portion of the drawing where
you want it. When you are satisfied with the position tape the template in place.

Using the center punch and hammer, mark the locations of the four mounting holes and the four corners of

the cutout area. Remove the template drawing.

Mark the perimeter of the cutout area. Drill a hole inside the perimeter of the cutout area to enable you to

cut the area out with the saw (the 1” hole saw might be used for this).

Cut the area out.

1.6.

Prepare the DiSEqC Switch mounting Locations (ST14D Only)

Prepare the mounting locations for the DiSEqC Switches. One switch assembly is required for each receiver that will be

installed. If you are installing multiple receivers one of these switches must be designated as the Master DiSEqC

Switch.

1.7.

Prepare the Multiswitch mounting location (ST14D and ST14M w/ 3+

receivers)

Prepare the mounting location for the Multiswitch to be installed. Refer to the manufactures manual for actual

mounting dimensions and any other applicable installation instructions.

1.8.

Prepare the Satellite Receiver and Television mounting locations

Prepare the mounting locations for the satellite receiver(s) and television set(s) (or monitor and stereo sound system).

Содержание ST14





















































































Результаты поиска

Содержание ST14

Отзывы:

Похожие инструкции для ST14

Бренды по названию

Популярные бренды

Sea Tel ST14, Руководство по установке и обслуживанию

Результаты поиска

Содержание ST14

Отзывы:

Похожие инструкции для ST14

Бренды по названию

Популярные бренды